Jump to content
SAU Community

Recommended Posts

Guys noticed for a while now, especially after going to the drags that if I'm cruising and lightly accelerate up to speed I get a whine coming from the rear, if I pop it in neutral the sound goes away

I'm guessing my diff is on it's way?

How much does it cost at an estimate to rebuild the stocker? Or is it time for an aftermarket jobby and rip skidz

Link to comment
https://www.sau.com.au/forums/topic/442331-my-diff-possibly-on-its-way-out/
Share on other sites

crown, pinion, bearing and possibly a clutch pack? get a quote from diff specialist then then think about a wreckers diff with warranty and a couple of hours under the car.

Personally I would be inclined to go with option 2

I have no experience with skyline diffs, but most lose the bearings first, then obviously if you keep driving, the crown and pinion eat themselves, and most people do keep on driving.. ffs

complete rebuild is expensive, so a nice little wreckers jobbie, can be a smart choice

It's been doing it for a while, went drags again lol seems to get worse now

On another note I have an early r32 gtr with the "fins" on the diff, and advantage of going later model without the fins ? Like from a late 93/94 model? Or are they all the same

have you ever changed the oil in your diff?

I know your 32 has plenty of ponies but if it still has the factory oil in it, then that is possibly why it failed and not the extra grunt.

.... My gtst has a finned alloy cover.

Edited by Missileman

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...