Jump to content
SAU Community

Master Cylinder Kit - Where To Source In Sydney?

Marko R1
 Share

Recommended Posts

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

Thx Duncan :) race brakes is where I bought my pads from yrs ago...what is the name of that brake fluid u recommended to me yrs ago? I know I had to buy it from MCA motorcycles as only they had it in stock at the time.

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

So I spoke to Matt and he suggested buying a second hand unit. To rebuild is 275 versus 125 for a second hand from justjap.

I get 30 days warranty and besides that, justjap haven't had one come back faulty in 15yrs after talking to Darron :)

Marko R1 Grand Master

Marko R1

Posted
  • Author
Posted

RBF600 is very hard to get but I finally found it, I used just over 1 bottle and the job is done!

Bleeding the calipers was very easy, however, bleeding the ABS was a challenge with the bubbles in the front nipple, rear nipple on ABS was easy though.

I followed the sequence as per workshop manual as I used to always apply pressure THEN release the nipple...with the GTR it's not necessary and in fact can be done with 1 person. You simply hold the peddle down for 3 sec then release and repeat this step until no more bubbles.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      Skid pans in/around Sydney?

      By The Bogan · Posted

      Dragging some reo behind a ute or trailer will smooth out a dirt road, I've used reo a few times to do unsealed road maintenance when we didn't have any plant available  It's best done when the dirt is wet though, and then you just let it dry out for a day to harden up For wetting the dirt I've used some 44 gal drums in a ute or trailer, and a water pump connected to a hose with a old sprinkler tied to the reo to wet the material down whilst spreading Basically just drive slowly up and down the road a few times dragging a few sheets of reo wired together with the sprinkler wetting it all down as you go
    • The Bogan
      Skid pans in/around Sydney?

      By The Bogan · Posted

      I did a motokhana years ago with ??Sydney Sporting Car Club???, it was on a grassy paddock and was heaps of fun, I think it was north west Sydney IIRC The old R33 boat was covered in grass and dirt, but nothing that a good wash and detail didn't fix And thinking back, when SAU did the airstrip run in Goulburn years ago, where the old 33 won highest RWD MPH, the quickest RWD ET on the airstrip, and best paint IIRC (before the runs down the airstrip) the damage to the rear quarters from stones flicking up required them the get a respray  I would definitely do a grass motokhana again in the MX5 Who knows someone that owns a farm with a big empty paddock  Liability these days is a big issue though
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      No intention of driving the car the way it's set up now, just wanting to make sure I haven't made any mistakes along the way so that the tune can go smoothly, I don't want to waste anyone's time with stupid issues. And of course I intend to get it towed to the dyno in a completed state 😅 I have the base fuel pressure with the vacuum disconnected set at about 40psi, which I believe is at least relatively close to stock fuel pressure, maybe I'll have a fiddle with the reg and see what happens. For all I know I could be wasting my time with this and I should just plumb it in and see what the tuner reckons. I just find it a bit strange that it seems to be under so much load just free revving, but maybe that's just a result of the turbo slowing down the exhaust gasses and making a restriction in the flow, with no boost to compensate.
    • The Bogan
      MLR's Bogan cruise ship

      By The Bogan · Posted

      The boy just hit up google translate and it worked a treat, he said step one was "please urinate with precision and elegance", he then sent me the correct translation  I get some new loctite for the small fixtures tomorrow and get some "dort" going after that 🤣
    • Kinkstaah
      RB25 S2 Idles but doesn't want to rev

      By Kinkstaah · Posted

      Right, so is the fuel pressure the same as it was previously? If not, well, it's not going to work well. I can understand the theory I assume you are going for, which is: "Run it N/A, and if I have the original AFM, and same amount of fuel and intake air as previously, the fact there's a turbo in my exhaust should still make it run" Which it... might? Provided you don't actually change how much air or fuel is going into the car.. or getting out. But if you have changed that, all bets are off. What is the purpose to even have the car run this way? To get it to a tuner? And if the goal is to limp it to a tuner, you're still going to what - plumb up a whole intercooler system and new intake in the parking lot out front before your tune......?
×
×
  • Create New...