Jump to content
SAU Community

Greddy/trust Geniune Td06Sh 25G 8Cm Complete Kit Rb

perzn_34
 Share

Recommended Posts

perzn_34 Experienced

perzn_34

Posted
Posted

Hey guys for sale is my GENUINE Trust/Greddy TD06SH 25G 8cm (responsive). This comes with the whole kit including the

Greddy turbo

Greddy exhaust manifold

Greddy external waste gate

Greddy dump pipe

Greddy exhaust housing heat shield

4inch intake

All the braided lines and fittings

All gaskets and bolts

This is an outstanding setup, all made to work together for best performance. The compressor housing is professionally sprayed black for stealth and a neat look.

Its still fitted to the car so u can come test it before i get it removed. Its seriously an awesome turbo kit for the rb engines.

For fitting you can just unbolt the manifold from the head and unbolt the dump form the rest of the exhaust and drop it in your engine. CANT get more bolt on that this.

Its don't very little work. Was installed march 2013 when the whole car got built and only had 5-7000km on the motor on street, was more of a show car.

Made a very strong 320rwkw on 18psi. Easy 360+ on e85.. Not for the faint hearted i should say

Only reason for sale is that I'm going a different direction with the whole car and motor.

Asking $3500 (brand new retails close to 7k) … grab a bargain

contact Andrew on 0450232121

Melbourne but can't post very cheap

Also have a matching intercooler and piping, and also a 3.5 inch HKS exhaust for sale too if your interested. All already on the car and can be tested.. Get in before i remove them :)

post-72334-0-84654700-1399046565_thumb.jpg

post-72334-0-33148500-1399046573_thumb.jpg

post-72334-0-39467700-1399046718_thumb.jpg

dorifticon Community Regular

dorifticon

Posted
Posted (edited)

Hey mate I take it this is for an RB26dett cylinder head?

I'm currently running a rb30dett setup in an r32 GTR and looking to go to single turbo.

Currently running 22psi with twin HKS 2530's.

couple questions:

1) will this fit r32 GTR?

2) can you post a pic of the turbo installed in the engine bay - want to get an idea of clearances because my cylinder head is sitting 38mm higher. Ideally, can you post a pic of the height of the turbo/plumbing relative to the height of the rocker covers? (ie like the photo you have but from a lower angle, it's hard to tell how high the turbo sits)

3) does this include some kind of dump/front pipe setup to connect up to the stock cat converter position?

4) what is the diametre of the outlet on the turbo? Does it have some way to connect to the stock intercooler setup?

Edited by dorifticon
  • 2 weeks later...
  • 9 months later...
  • 1 year later...
perzn_34 Experienced

perzn_34

Posted
  • Author
Posted

Back up for sale again.

Kit now includes:

Greddy turbo (8cm rear housing)

Greddy exhaust manifold

Turbosmart Hypergate45mm external waste gate

Greddy dump pipe

Greddy exhaust housing heat shield

All the braided lines and fittings

All gaskets and bolts

Now fitted to my r34 gtt and still in the car so if you are early you can get a test drive. Making 322rwkw on 18psi on BP98

Reason for sale is going bigger turbo.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...