Jump to content
SAU Community

Anyone Else Using Penrite 5W-30 On Their Vq35?

rambocarebear
 Share

Recommended Posts

rambocarebear Contributor

rambocarebear

Posted
Posted

Guys,

Recently flushed the oil and replaced it with this and ever since the engine sound and whilst driving the car, it doesn't seem to be running at optimum performance. It is very strange. Best way I can describe is as though the performance of the car after the oil change is performing like a car that is due for an oil change... .

Anyone able to offer feedback on this ? Am I using the wrong oil ?

Car has got 78kms on the odometer

Link to comment
Share on other sites
The Max Mentor

The Max

Posted
Posted (edited)

I use Penrite HPR5 5W40 in mine but it's a VQ37VHR motor. At any rate, I've always used either Penrite or Amsoil depending on the required viscosity on all my vehicles. Never had an issue.

Edited by The Max
Link to comment
Share on other sites
Nightcrawler Grand Master

Nightcrawler

Posted
Posted

I literally changed my Nulon 10W40 to Nulon 5W30 when I serviced my 35 today. Haven't driven it properly yet, but can report back tomorrow night after I have done some km in it tomorrow if you want.

Link to comment
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

Oil viscosity is critical to camshaft actuation, and changing the grade will mean the ecu needs to re-learn the camshaft PWM input figure for a particular advance target. This should happen eventually over time, or it may need to be done via the Nissan consult software. Probably easier for you to dump the 5w30 and put some 10w40 in there, it should feel a lot better.

You may have also dislodged some burnt oil varnish with the flush, which has partially blocked the little filter in the actuator solenoid.

In a nutshell, run a 5w40/10w40 and stick to it, and change your oil every 5k.

Link to comment
Share on other sites
ARTZ Grand Master

ARTZ

Posted
Posted

Bloody shitty nissans...I change the oil in my Honda every 10k with factory spec 5-30...i even changed it to 10-40 and 10-30 once......vtec still worked fine yo!!

Link to comment
Share on other sites
sonicii Veteran

sonicii

Posted
Posted

Bloody shitty nissans...I change the oil in my Honda every 10k with factory spec 5-30...i even changed it to 10-40 and 10-30 once......vtec still worked fine yo!!

Isn't VTEC just 2 fixed cam settings and it switches between them? if so, it is a bit different to variable valve timing on the VQ.

anyway, I have run castrol edge 5W-30 in mine since I have owned it, without any issues.

Link to comment
Share on other sites
Hertz Donut Proficient

Hertz Donut

Posted
Posted

Just changed the oil in my PNM35 (also on 78,000km) to Penrite HPR10, which is now rated at 10W50. Not ideal but I'll see how it goes, it's generally just puttering around town at the moment on shorter trips.

Link to comment
Share on other sites
ARTZ Grand Master

ARTZ

Posted
Posted

Isn't VTEC just 2 fixed cam settings and it switches between them? if so, it is a bit different to variable valve timing on the VQ.

anyway, I have run castrol edge 5W-30 in mine since I have owned it, without any issues.

f**ked if I know, who cares its a honda...lol...

it does use oil pressure to switch between setting i think though....or something like that :wacko:

Link to comment
Share on other sites
  • 5 months later...
Hertz Donut Proficient

Hertz Donut

Posted
Posted (edited)

Heh, I just changed to a 5W30 (Castrol Edge Titanium, was on special at Supercheap) and haven't noticed any difference, although I should really check the oil level to see if it's using any up.

PS: The VQ35 dipstick still sh!ts me to tears, so damn hard to get out without scraping all the oil off in the first place, and then nigh-on impossible to get back in again. I swear the dispstick is the best (and only good) thing about my POS Commodore.

Edited by Hertz Donut
Link to comment
Share on other sites
scotty nm35 Grand Master

scotty nm35

Posted
Posted

PS: The VQ35 dipstick still sh!ts me to tears, so damn hard to get out without scraping all the oil off in the first place, and then nigh-on impossible to get back in again. I swear the dispstick is the best (and only good) thing about my POS Commodore.

So why check it? Just dump the 5L in and be happy for 5K.

Link to comment
Share on other sites
Hertz Donut Proficient

Hertz Donut

Posted
Posted

Funnily enough that's exactly the tactic to which I've resorted. Oil change every 3 months means there should be something left in it, and I got the same amount out as I put in last time I changed it (start of this month) so it seems healthy enough.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • OST Micah
      RH9 R32 GTR Build Thread

      By OST Micah · Posted

      A year of slogging through this bearing issue and finally fixed. What a nightmare. The oil pressure increase did not fix the problem. If you would like to read all the details in case you ever run into a similar issue visit my thread on Yellow Bullet. https://www.yellowbullet.com/threads/continuous-rod-bearing-issues.2689569/?post_id=74193031&nested_view=1&sortby=oldest#post-74193031 In the end the rod bearings themselves were the issue. I had switched from ACL (first engine) to King because that was all we could get at the time and I thought nothing of it. Put the ACL's back in after a year of taking the pan off multiple times to change many things. Issue resolved. Can't believe it was just the bearings themselves all along. It has now been about two years since I drove the car on the street or had it at the track. At some point I had installed all solid and spherical bushings in the rear but had never aligned it since it just went on and off the dyno. Alignment was the first thing to do. (Old photo but same concept) Then I took the transmission out and went through it. This was my first gearset install and I've done about 15 since this one and learned a lot and wanted to apply some of these tweaks to mine. The aftermarket shift forks take very well to some modification and I wanted to make that change. Shifts are now super smooth and no having to find the gear. I also recut the 5th and reverse shift sleeves - always wanted to try this and see how well it works. It works very well! No grinds or having to do a second attempt going into reverse and 5th is perfect. Before During After Going back in In rummaging through my spare trans parts box I found the only parts I've ever broke on a stock trans; the 3-4 shift fork - twice!  
    • Kinkstaah
      R32 Gtr Long Term Love, Now Project

      By Kinkstaah · Posted

      It also depends on gearbox ratio. Those drag cars running 7s passes aren't doing it on an overdrive gear ratio (probably). 1:1 is "fine", the critical RPM for a 50' single driveshaft in chromemoly is 6900rpm.... ....but when you shift into 5th and use 0:73 or 0:8 it all changes. Do you know their rear diff ratio? etc. That's the stuff that matters with regards to it. Whether it actually matters given your use application is also relevent. You may never get into those scenarios, like most ruined GTR's from Western Sydney don't :p
    • Dose Pipe Sutututu
      R32 Gtr Long Term Love, Now Project

      By Dose Pipe Sutututu · Posted

      but for how long? would it handle a few laps around SMSP in anger? 
    • GTSBoy
      R32 Gtr Long Term Love, Now Project

      By GTSBoy · Posted

      And over it. Need to stop it coming through the floor.
    • Duncan
      RB30 Struggles from idle

      By Duncan · Posted

      Is it running the standard ECU? some sort of data log might help understand where timing, AFRs etc are at.  If it is standard ECU something like Nissan Datascan would help
×
×
  • Create New...