Jump to content
SAU Community

Some Stuff For Sale - V35 Coupe


Recommended Posts

Hey Guys, I have a few things I'd like to sell:

Coupe Headlights $550 (these sell for $750 on Ebay) - Bought new so I could restore the stock lights, only fitted for about 6 months - great condition - RHD specific. One small issue effecting the drivers side light, I hadn't fitted the cap to the back correctly and at some point the light got water inside. The 1st I was aware of this was when the balast failed, I poped the headlight out and inverted it to remove the balast - didn't realise there was water inside and now there is a slight water mark on the inside of the lense. These lights DO NOT leak, the caps where that cover the back of the bulb press on and I hadn't seated one correctly. Happy to refund if new owner finds otherwise.

IMG_1881_zps84f1a139.jpg

IMG_1882_zps03e42eda.jpg

IMG_1883_zpscbca2f39.jpg

IMG_1884_zps0dabad58.jpg

The water mark shows up with the camera flash, it is hardly visible in real life.

IMG_1887_zps218ace96.jpg

IMG_1886_zpsf853aa61.jpg

IMG_1885_zpsc9c3ff02.jpg

Tailight Eyebrows $20, bought these but due to my car being wrapped it was easier to just vinyl the tailights, so I don't need these. Will require double sided tape to fit.

IMG_1880_zpsf368a93b.jpg

Subwoofer - Alpine Type R 12 inch dual 4 ohm $130, bought 2 of these but only need one, really solid subwoofer, great sound and can handle stupid power.

IMG_1866_zps6803e281.jpg

IMG_1868_zps8294b779.jpg

IMG_1867_zps6ddfa43e.jpg

Subwoofer and Enclosure, Kicker 12 inch $70, was the sub before I upgraded to the Alpine, plenty of punch and lighter than the Alpine!

IMG_1863_zps426a70ba.jpg

IMG_1862_zps32f49204.jpg

IMG_1864_zps425dadeb.jpg

SOLD, come and pick it up! Had this on the shelf for years - OK performance. Box is solid - was a test bed for the Alpine, fits in a coupe boot!

IMG_1865_zps5be3ad0d.jpg

All are for pick up at Ormeau (1/2 way between Gold Coast and Brisbane) or I work at Eight Mile Plains so could meet nearby. Could post the headlights, but the rest is pick up only.

PM or Call on O435 735 9OO

Thanks

Shane

Edited by Superpoo
Link to comment
Share on other sites

Just out of curiosity why did you revert back to stock headlights? Could be interested as I just bought a black 03coupe that these would suit.

Always intended to revert back, I had attempted a projector conversion that failed miserably so went with these whilst I repaired the stock. To be honest these lights have excelent output and I believe are better performers than the stock, thought long and hard about selling these.

Link to comment
Share on other sites

Link to comment
Share on other sites

  • 2 weeks later...
  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share



  • Similar Content

  • Latest Posts

    • People still have Skylines? I thought they're non-existent now. 
    • Harness update time have had great fun and learnt so much already so far with this project. I started off making both the ignition and injector sub harnesses in the hope any mistakes i made here aren't as hard to undo and learn from as the main harness.  A cool comparison of the old harness using presumably TXL wire and the new which is using Tezel. Also opted to use DTM plugs to keep the whole setup as neat and tidy as possible and tucked the wiring under the coil bracket to try and keep it all from sticking out too much. Although the injector harness, I'm not overly happy with as I'm still using the rubber boots that are supplied with the type of plugs it just looks ugly and sticks out like a sore thumb with the white identifiers so a slight redesign may be done.   Then it was main harness time and most importantly trying to route it nice and away from the heat it will use the OEM heater hose routing which is no longer present to keep the harness up high and secure. it's amazing how much smaller this harness is able to be compared to the old one. plugged everything into the emtron and with the help of the tuner again attempted to start it up and instantly fired up and running smoothly on all 6 which was a big shock to myself. So still some routing and adjusting to be done for the final fit up and installing a knock sensor harness plug which is in the post all has gone surprisingly well.     The old harness for shits and giggles.
    • They do that at random every now and then, with almost no detectable cause. Mine has done it a couple of times (over 25 years!!). Never worked out why.
    • I don't post on here and have been lurking for some time now. Many of the topics have helped me out more times than i can count. I was racing yesterday (11/9) and blew a front right CV shaft. I have spares so I popped a new one in. A thread i read previously said to check the engine mounts if you blow a front CV. Upon inspection, the front right mount was completely separated from the upper plate. This discovery saved me time and money, because i would have blown another CV if i went back out. Just wanted to thank you guys and wish everyone luck with with their builds. (Now if we could only come up with a solution for my power steering belt flying off after hitting the rev limiter, lol)
    • Either way he still need those style of spacer to go into the manifold because the photo he currently has is not going to work 
×
×
  • Create New...