Jump to content
SAU Community

Recommended Posts

Hi I'm after a complete setup to suit a series 1 Rb25 I'm after a whole setup including ecu injectors turbo ect I won't something map sensor based cash waiting must be located in Sydney

Also I'm after a twin turbo kit to suit a Rb25 pm me wot u Hav thanks

Removed from R34 Neo

Made 320rwkw

Autronic ECU with Haltech 3 Bar Map sensor

Loom for R34 Neo engine

Plazmaman Race Series Intercooler + pipe work

Garret 3076R Turbo

Tuneagent Highmount Manifold

Turbo Oil/Water braided Lines

3.5" SS Dump and front pipe to suit R34 (you will need to shorten the pipe by 18cm to make it fit an R33)

SARD 800cc Injectors

SARD Twin entry fuel Rail

4" Intake Pipe with K&N Filter

Complete package, only part I have sold is the Greddy Plenum, other than that comes with every part needed to bolt and and make power.

All parts are used, but in good condition.

$4000

I would Hav to pass on that setup mate I'm only working on a 2500 budget I'm after a setup to just bolt up plug in an go with urs I would need to get it returned an play around with looms ect thanks for the offer but

This is my setup atm but I'm finding the Holset a little laggy for the engine

I Hav a Rb25 neo engine on a R33 series 1 computer an loom micks metal craft forward facing plenum top mount 6 boost manifold split flange T3 turbonetics external gate front mount intercooler 3 inch exhaust split fire coils sard fpr big fuel pump setup I Hav a Holset hx35 on it atm but I'm finding it abit to laggy an it needs a rebuid soon so wot im after is a tuned computer preferably a power fc jetro or something else map sensor based bigger injectors an a turbo not as laggy an better suited to my engine im looking for something that will be good for around 280 rwkw an it must be located in the Sydney area but will travel a little for it cheers w

I Hav found the turbo an computer I need now I only need a good set of R33 something around 1000cc. Also still after the Rb25 twin turbo kit for another project car I Hav

I have a complete twin turbo kit off a rb26 with nismo turbos, afm's and greddy pods I'm chasing $1500 posted anywhere. Then just get a manifold made from 6boost

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • So was there a solution to this problem? I’m having this issue now. 
    • not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...