Jump to content
SAU Community

Recommended Posts

So I changed my timing belt, tensioners and water pump but I was apparently not paying enough attention to the instructions and now I'm worried.

Before I removed the belt, I only lined up the timing marks on the two cam pulleys up top and didn't pay attention to the mark on the crank. I was careful not to move anything, but the belt was hard to get on so now I'm worried that something might have moved.

I haven't fired the motor yet and I don't want to until I know this is right. So any advice on what I should do? Is there anyway I can safely check that it's lined up correctly?

A screwdriver down the first bore can give you close to top dead centre, then make sure the marks are correct on the cams.

Make sure you turn it over by hand first a few revolutions. That way you can be sure the valves aren't hitting the pistons.

Ok so I need to get cyl 1 to tdc on the compression stroke, and at that point the two marks on the cam pulleys should line up? What about the mark on the crank - should that line up with the notch cut out on the bottom side, or should it be at the 0deg timing mark on the belt cover?

and if it turns easilly by hand (besides the resistance of compression) then the pistons arent hitting?

Edited by mistermeena

ah yep so when cyl 1 is at tdc, the crank gear mark will be lined up with the notch on the oil pump? And if it's wrong on the cam gears I need to take the belt off and adjust them in the direction closest to making them line up?

Seriously hope it all lines up lol

Belts are a bit hard to get on, abit harder when they are new. You have to get them started on each sprocket, idler & then tensioner, then evenly push the belt on all the way around, it's the easiest way.

If you have doubts, before turning the engine over, get a mirror & visually sight that crank & cam marks are lined up. Then, slip the lower cover on & sit the balancer on the crank nose by hand & see if your marks line up. Then if all good, release your tensioner, bar the engine over 2 revolutions, re-check all 3 marks. If it's good, then hold the eccentric in that position with an allen key (please, do not add more tension, your only causing premature stretch in the belt & loading the idler & tensioner bearings unnecessarily!) & torque up the bolt.

If your in Sydney I could come & have a look.

ah yep so when cyl 1 is at tdc, the crank gear mark will be lined up with the notch on the oil pump? And if it's wrong on the cam gears I need to take the belt off and adjust them in the direction closest to making them line up?

Seriously hope it all lines up lol

Correct.

Not exactly. The procedure is once you get the timing belt on, you rotate the engine backwards to put tension on the belt (Think it reccomends turning it over 3 times backwards by hand) then get an allen key to fit in the tensioner just to hold it in that position while you do it up.

I think thats right anyway. something along those lines anyway

Never ever turn an engine backwards (anti - clockwise)!

When fitting the tensioner, you need to wind up the spring so that after you have fitted the belt & release the tensioner BEFORE winding the engine over (clockwise) by hand, you actually already have spring tension applying force on the belt.

The whole purpose of winding the engine over (clockwise) is remove any slack from the installation process before torquing the bolt.

It just makes it hard to align the marks, as the slack is on the wrong side. Cam timing is important to get right.

I saw an RB26 actually running backwards the other day, both cams were 90 degrees out, set up like Toyota cam wheels accidentally. Exhaust was coming out the airbox and fresh air sucking in the exhaust. Once the marks were realigned properly it ran fine, didn't even bend a valve.

  • Like 1

ah yep so when cyl 1 is at tdc, the crank gear mark will be lined up with the notch on the oil pump? And if it's wrong on the cam gears I need to take the belt off and adjust them in the direction closest to making them line up?

Seriously hope it all lines up lol

Not to put too fine a point on it but with No1 at TDC you can still be 180 out on the cams.

So don't panic if the cam marks don't appear with No1 at TDC.

Turn the crank another revolution and then see if the cam marks are looking better when referenced against the back cover.

Don't take any notice of markings on the belt at this stage.

Not cranking an engine backwards harks from timing chain engines with hydraulic tensioners. With the engine cranked backwards, the spring pre-tensioner may be insufficient to keep the chain on the sprockets.

I saw an RB26 actually running backwards the other day, both cams were 90 degrees out, set up like Toyota cam wheels accidentally. Exhaust was coming out the airbox and fresh air sucking in the exhaust. Once the marks were realigned properly it ran fine, didn't even bend a valve.

Yep saw the same one as you Scotty, the issue was they were black tomie cam gears and the dot was not highlighted in white, silly bugger set them up like 2Jz gears not seeing the dot.

When i got home i looked at my gears and the dots had a dab of white paint on them, go figure, maybe not genuine tomie cam gears?

I had a backup set of valves on my bench if he needed them, didnt in the end, it surprised me.

That car ended up back on the hoist a few days later, they had setup antilag on it and a new clutch, owner spent the next day doing launches showing his mates and destroyed the clutch, never gave it a chance to bed in properly.....

It just makes it hard to align the marks, as the slack is on the wrong side. Cam timing is important to get right.

I saw an RB26 actually running backwards the other day, both cams were 90 degrees out, set up like Toyota cam wheels accidentally. Exhaust was coming out the airbox and fresh air sucking in the exhaust. Once the marks were realigned properly it ran fine, didn't even bend a valve.

Yep saw the same one as you Scotty, the issue was they were black tomie cam gears and the dot was not highlighted in white, silly bugger set them up like 2Jz gears not seeing the dot.

When i got home i looked at my gears and the dots had a dab of white paint on them, go figure, maybe not genuine tomie cam gears?

I had a backup set of valves on my bench if he needed them, didnt in the end, it surprised me.

That car ended up back on the hoist a few days later, they had setup antilag on it and a new clutch, owner spent the next day doing launches showing his mates and destroyed the clutch, never gave it a chance to bed in properly.....

Hahahahaha RB26 Honda engine!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha thanks everyone, I'll take everyone's suggestions into consideration. If I do eventually choose a car ill post it here update on the mods I do.
    • I found the ingredients at larger amounts from a Coffee Shop. 1kg Citric Acid for €8.50 500g Baking Soda for €2.50 I tried it out tonight distilled water (I got from my ACs) and dish soap. It does get bubbly with dish soap. In just two hours the hanger has improved significantly and rubbing against any remaining rust seems to flake it off. I'm going to leave it a little bit longer and see how it goes. I have read that someone even used this solution in an ultrasonic cleaner to clean a seized water pump which brought it back to life.
    • If you like more modern stuff than the R series, you should check out a V37 400R, they are pretty mod friendly
    • Haha luckily we don't have emissions, inspections, or any laws against power adders here. They only thing they somewhat keep an eye out for are ridiculously loud exhausts. 
    • Just wanted to pop in an update on my setup. The CD swap has been great, I love the mazworks housing for the overall simplicity. I ended up sealing my trans tunnel with a thin sheet of aluminum reused some of the holes on the trans tunnel, and laid some window sealing EPS foam around the edges. Works great, really quieted things down and sealed up the car.  As for the power comment. Right now I am also running about 650whp. with the way the bell housing is attached to the face of the transmission I have zero doubts it would be fine, mainly because the input shaft and main shaft bearings are seated into the bell housing adapter. This means the load is NOT on the bolts to maintain the power, rather into he casing of the bell housing; Yes the bolts are doing some work there, but with both shafts locked in zero worries.  End of the day, the Mazworks solution is the easiest and safest. no need to take your trans to a shop to get milled perfectly, it fits with minimal clearancing, and you can use all your existing clutch and flywheel.  Driving wise the CD has been great compared to the big box, I'll probably swap my final drive at some point. The serial 9 shifter is gooooood, my only qualm is how tight it is, it takes a fair bit to get use to, 5th and 6th are a bit eh/hard to find at times, but maybe I need re-adjusting, and I think my clutch master is very tired and needs a rebuild. 
×
×
  • Create New...