Jump to content
SAU Community

Gates Timing Belts

Adz2332

By Adz2332,
in General Maintenance

 Share

Recommended Posts

ZED X Rising Star

ZED X

Posted
Posted

I'm running a gates one on my R.

It was pretty noisy initially however i found that i had over tensioned it (very slightly). Was fine when cold but when at operating temp it would make a distinctive whine.

Loosened it off a tad and its been fine since.

VLSteve Enthusiast

VLSteve

Posted
Posted

Yeah Zed, been there done that, who needs to do the job 2X ???

Will never touch another kevlar belt.

Nissan belt FTW.

I Agree!

Had one on my daily drive, after adjusting it a couple times, I ditched it for a Nissan belt

jiffo Mentor

jiffo

Posted
Posted

I found a Gates belt can run as silently as a stocker, it's all to do with belt tension.

Unless you're fitting belts everyday, you lose the "touch" and kevlar belts require slightly less tension than factory.

So the average handy-bloke ends up doing the job twice, or perhaps get the job done poorly by an expert and believe their spin that the noise will go away in time.

Nobody likes pulling it all down (especially an Rb26) just to slacken off a tad, which is why no more kevlar belts for me.

Who else remembers Rob (RIPS) offering his car if anyone could find a non-factory Nissan engine part on his early R32/Rb30?

It made considerable Hp.

jiffo Mentor

jiffo

Posted
Posted

I found a Gates belt can run as silently as a stocker, it's all to do with belt tension.


Unless you're fitting belts everyday, you lose the "touch" and kevlar belts require slightly less tension than factory.


So the average handy-bloke ends up doing the job twice, or perhaps get the job done poorly by an expert and believe their spin that the noise will go away in time.


Nobody likes pulling it all down (especially an Rb26) just to slacken off a tad, which is why no more kevlar belts for me.



Who else remembers Rob (RIPS) offering his car if anyone could find a non-factory Nissan engine part on his early R32/Rb30?


It made considerable Hp.


Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      WTB noltec r32 front upper (camber) arms

      By GTSBoy · Posted

      I'm firmly on the "zero compliance is good compliance" for FUCAs. I'd be looking to solid metal joints even if the primary reason for having them is because they facilitate the twist in the arm. I have never been more happy with the way the front suspension behaves than I have since I got rid of the FUCA bushes. Even the thin little (short lived) poly bushes in the Whiteline adjustables have too much compliance for my liking. It probably won't be long before I have sphericals nearly everywhere, probably including both top and bottom arms in the rear, and I'll start complaining about the increased costs for dental work. But I will be enjoying the driving more, I'm sure.
    • GTSBoy
      Brake pad Compound suggestion

      By GTSBoy · Posted

      Plus, you'll get great experience in bedding in pads!
    • Matvei27
      WTB noltec r32 front upper (camber) arms

      By Matvei27 · Posted

      I have offset Nismo brackets so the fact the gktechs can pivot is less important to me. I have 170mm JIC arms with bushings - but they provide no adjustment and I'm not sure whiteline eccentric bushings will fit them (I don't want to ruin the bushings currently in them to find out). Ideally I want something with bushings + adjustment; hence why I'd like to find a pair of these. Unfortunately they aren't easy to find.
    • Murray_Calavera
      Brake pad Compound suggestion

      By Murray_Calavera · Posted

      @Vee37 How much do you really care about finding these pads again? If your pads are quiet, work well and produce minimal dust, really isn't that enough? If you are set on finding the exact pads again, I suppose I'd do something like this -  Visit your local Jax, find out what brand of pads they carry. If the Jax workshop you previously went to had the pads on the shelf, then you can almost guarantee it will be of said brand.   I'm guessing you don't have the receipt for the previous work and pads. Can you visit a Jax workshop and see if they can look up your previous job to see what pads were fitted?  Still no luck? Put your stalker hat on, find the staff that used to work at the Jax store and ask them. Talk to local workshops, try to find out where the mechanics went to. Talk to Jax workshops, maybe they relocated to another workshop. When it comes to mechanics, its a small world. You'd be surprised how easy it is to track someone down. If these ideas don't work, shit will start getting crazy very quickly.... You could find out every brand and model of pad that fits that car... and try them individually ticking each off the list if it wasn't the one you were looking for.... If you go down this path your going to want to learn how to swap pads yourself, it is very easy, takes minimal tools and space. If you have room to park the car you have room to swap the pads. Plus you have the advantage of making sure all the brake hardware goes back in so they won't squeal! 
    • MBS206
      Beers and skylines Fatz style

      By MBS206 · Posted

      You miss spelled bearings...
×
×
  • Create New...