Jump to content
SAU Community

Recommended Posts

So for sale I've got a pair of garret/hks gtrs turbos, they've only done 12,000kms in good condition no shaft play

Hks pulse exhaust manifold , with no cracks

Hks dump pipes with new o2 sensors

Apexi bends with pod filters and standard air flow meters in good working condition

Xforce crosspipe 3.5 inch stainless steel

Brand new never used genuine Bosch z32 airflow meters with plugs.

Standard exhaust manifolds with no cracks

Standard oil lines and top turbo piping.

Nistune ecu

All this gear is to suit a r32 GTR skyline and is in good condition!

I'd like to sell all this stuff as a package deal but if I can't sell it after a few weeks I will sell stuff separately

$3500 Ono I live in tasmania and will post Australia wide at buyers expense. More pictures can be supplied if needs more

Call peter on 0438308757post-134876-14052035041128_thumb.jpgpost-134876-14052035181152_thumb.jpgpost-134876-14052035393171_thumb.jpgpost-134876-14052035593099_thumb.jpgpost-134876-14052035775768_thumb.jpgpost-134876-1405203592592_thumb.jpgpost-134876-14052036062525_thumb.jpgpost-134876-14052036244667_thumb.jpgpost-134876-14052036416774_thumb.jpgpost-134876-14052036676331_thumb.jpgpost-134876-14052036793331_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/445566-gtrs-turbo-upgrade-kit/
Share on other sites

Turbos $1100each

Hks manifold $500

Hks dump pipes with O2 sensors $400

Apexi pod filters and bend and standard afm's $250

Z32 afm's $475 for the pair

Nistune ecu $400

Stock piping and oil lines $120

Gtr r32 intercooler good condition , no brand $250

Gtr injectors 444cc good condition and in good working order $250

Also have for sale a r32 GTR hks hard pipe kit for the intercooler with joiners and clamps $250

Sard fuel reg with gauge$150

Twin 044 pump holder $30 ( brand new)

Will get some pics up later this morning

  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Well some mostly good news and some slight bad news.  Good news is cylinder 6 did in fact only require a honing and I'm good to run my 86.5mm pistons again. I should also get the block back by end of week. Bad news, had a few surprises pop up. First, main and rod bearings were trashed. No sign of any heat damage. I knew right away what caused this... I had not packed my oil pump originally and spent a lot more time than I would have liked cranking the motor to get oil pressure. It sounded fine once started so I chucked it up to luck and forgot about it. Luckily rod and crank are fine and just need new bearings. Engine builder agreed that this was the cause.    Another surprise that carbon covered up very well that I didn't catch, something got sucked up and went through cylinder 1, 2 and 3. Luckily this was no cause for concern, just needed a bit of cleaning up. Valves look fine but he will vacuum test the head this week to confirm. I'm presuming this was something left over from welding my intercooler piping, but we'll never know. I'm going to thoroughly reclean everything.    So all in all, happy the motor is fine, and I'll get it back much sooner than expected. I'll also be taking the time to convert my WMI system over to direct port. I'll snap some pictures of that when the parts come in. 
    • I understand, thanks. Yeah I wouldn't want the car to tip over, I'll try and use the sills, I don't want to risk smashing the chassis rails. I ordered some rubber pucks that have a hopefully big enough slotting. If the front right gives me trouble I can always just make a wood block. I'll measure and inspect the sills closer once I actually take the car up. I hope so, but the rubber blocks I had in hand so far were pretty damn firm, if they are that hard they won't give much way. I'll let you know what happens. Angle grinding rubber isn't one of my favorite tasks. I'll probably start a build thread soon, for my own documentation and "log" as well as sharing what's going on with the car.
    • Kinda something I have been thinking about.  To be honest, we bought it already driving like that.  So there's no telling how long it actually has been driving like this.  Hopefully damage is too bad when we drop the pan.   I am having a hard time finding a site that sells the solenoid for the 5 speed auto, do you have any suggestions?
    • That'll be most likely down the road...  LOL  
    • a stock / option or aftermarket?
×
×
  • Create New...