Jump to content
SAU Community

Dyno Variances

djvoodoo

By djvoodoo,
in Engines & Forced Induction

 Share

Recommended Posts

juggernaut1 Proficient

juggernaut1

Posted
Posted (edited)

Whilst not directly on topic - post 17 of the following link shows the different hp figures obtained using different shootout modes with the same car on the same day ( I knew turbo 4 cylinders were handicapped in shoot 4F :P ).

Notably, the second last dyno shows the effect on hp when the temp probe is placed near a heat source.

http://www.fordxr6turbo.com/forum/topic/59178-power-differences-between-shootout-modes/?hl=dyno

Edited by juggernaut1
juggernaut1 Proficient

juggernaut1

Posted
Posted (edited)

Take 2

Shoot4

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0007-1.jpg

Shoot 4F

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0006-1.jpg

Shoot 6

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0005.jpg

Shoot 6F

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0004-2.jpg

Shoot 8

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0003.jpg

Shoot 8F

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0002-2.jpg

Shoot 6F - Hot intake probe

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0009-1.jpg

No Shootout Mode

http://i198.photobucket.com/albums/aa292/The_Boganxr6t/DSCF0008-1.jpg

Edited by juggernaut1
scotty nm35 Grand Master

scotty nm35

Posted
Posted

1/4 mile/ MPH for finding out how much usable power you have, as stated before dyno for tuning.

Is that still a reliable indication of power, even if my slug auto won't get off the line due to the stock stally stator?

33GTRV Mentor

33GTRV

Posted
Posted

Good friend of mine stopped posting outright power figures on his wall in his cell due to people not liking them reading lower than other shops, and I mean considerably lower, but like the big sign above his dyno reads, dynos lie, tracks don't . I'm yet to see a car that didn't run the mph on the strip that the dyno power figure suggested.

Jazzadub Enthusiast

Jazzadub

Posted
Posted

Power delivery. What you lost in peak power you may have gained everywhere else

Could be that. I don't have a dyno graph of the supposed 330wkw run on 98, but I do have a dyno graph of a 320wkw run on E85 (not the 260kw 98 run).
So less power on E85 than it supposedly had on 98, but its surely going to be faster.
I think there must have been some tweaking done of the ramp rate to achieve the 330wkw figure for 98.
This is the dyno graph of the E85 run, does it looks fast? It sure feels fast!
post-115803-0-24003800-1404958875_thumb.png

Feels faster or is faster?

Fair point, I've never been to the track so don't have any rock hard evidence.

Lets just say it definitely doesn't feel like it has had 70kw ripped from it!

XGTRX Veteran

XGTRX

Posted
Posted

Dynos are tuning tools. The absolute power and torque measurements are irrelevant unless being used for a comparison to a change being done to compare to a previous measurement on the same dyno but even then changes in the driveline can make it hard to compare.It is used solely for tuning to assess and optimize engine parameters by a skilled operator.

Example is my clubby that with a flash tune and diff gears measured 270rwkw and did 107mph.I installed cams with head work, hi stall and retune and measured 274rwkw and ran 112mph. Based on mph should be about 40rwkw difference. And based on mph it should be about the 285rwkw mark give or take. Moral of the story the tuner used the dyno to optimise the setup and mph told me how much power it really had. Hope this helps.

XKLABA Grand Master

XKLABA

Posted
Posted

You can strap a car down to tight and lose power as well :(

Unfortunately there are many things that will effect dyno reads including tyre pressure

As others have said a dyno is just a tool used for tuning and a vague indication of power, that said a dyno isn't going to shop 100hp on a 1000hp car and vise versa, if you think the operator is fudging figures for what ever reason and not just a low reading dyno, I would be going else where

Mph is the best indication of power v weight and ET is an idication of setup

I always take my car to the 1/4 mile track after I do something to it ( power wise ) to see real life gains for both MPH and ET

An example for MPH, I not long ago had my 34 tuned and right after that I went to the strip, knowing it would run a 10 I rolled off the line and shifted to second then nailed it for the first 4 runs to get an idea of mph and ran consistent 131-132mph ranging from 11.6-12.5 et, last pass full noise from start 10.8@132mph so the start doesn't make much if any difference on mph unless your still turning tyres half track :P

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      The 1000ccs are side feeds but they're not currently installed, had my old factory ones in for leak testing purposes, only decided on them because front facing plenums and good top feed rail kits are out of my budget at the moment, are they really that problematic? Had a set of yellow jackets that lasted me 5 years, no real issues, only replaced them chasing this misfire issue that ended up not being ignition related 😄  
    • Dose Pipe Sutututu
      RB25 S2 Idles but doesn't want to rev

      By Dose Pipe Sutututu · Posted

      Are those 1000cc side feeds? If so, that's part of your problem. I have 1480cc and they idle at stoich on 98RON, and all the way to E85. Also your coil packs.....
    • Trilbyte
      RB25 S2 Idles but doesn't want to rev

      By Trilbyte · Posted

      Update for the sake of closure   Ended up getting the intercooler piping all sorted, new plugs and yellow jacket coils, and she was idling mint until it warmed up while I was bleeding the cooling system. Found the misfire to be localised to cyl 3 by unplugging coilpacks, ran a compression test, that checked out, then decided to get a mate to check if that spark plug was firing out of the motor. Upon cranking it over, with the injectors disconnected, the car actually fired and ran on a couple cylinders and heaps of fuel came out the top of cyl 3 I'd say that injector's either spraying incorrectly or spraying far too much, which is fine as I'm planning on replacing them anyway I'm planning on making about 250kW on flex fuel, and have a set of 1000cc injectors from ozautosport, obviously overkill but I'm planning on building the motor and running more boost further down the line, do you reckon they'd be too big for a smooth idle on 98? Thanks for the replies gents, much appreciated
    • Dose Pipe Sutututu
      Any feedback on GReddy Turbine Kit T620Z in r33 GTST/RB25DET?

      By Dose Pipe Sutututu · Posted

      Nice modern Hypergear high flow would be perfect.
    • Murray_Calavera
      Steps to DIY sanding car back ready for respray....

      By Murray_Calavera · Posted

      I'm confused. You said you want to "remove the clear coat from most panels" but it sounds like you are actually doing a full respray? Few random things to add -  If you chase the blistered paint with 120 grit, I can almost guarantee you'll chase it down to bare metal (that's fine). But if you paint the car from here, you'll have nice little indents where ever the blistered paint was. The new paint won't magically level out the low areas, you need to fill them. Which leads me to the main point I wanted to add, make sure the whole car is flat before you paint it. All those areas with blistered paint you sanded out, make sure to fill them and triple check they are flat with a block guide coat. I'd also check the whole car is flat with a large block and guide coat but yeah up to you if you want to go that far.   
×
×
  • Create New...