Jump to content
SAU Community

Recommended Posts

Howdy

I have a very peculiar issue with my car at the moment.

On Christmas day, I was driving home and coming up a large Hill when suddenly my car stopped accelerating and slowly came to a halt. I thought possibly I was low/ran out of fuel, so luckily it rolled into a fuel station. I slapped $20 in, started her up and away I went for about 500m when the same thing happened again. That is, the car is accelerating and driving normally, then all of a sudden all engine power instantly disappears and the car comes to a stop (dash lights/stereo etc. continue to function as normal). After about ten minutes of trying to start/letting it sit, she started up again and I managed to get her home.

Thinking it was something electrical, I went over the entire wiring loom and came across a couple of minor things that seemed unlikely to be the cause, but I gave it a go. I took her out again and she was fine. Couple of weeks later I did a track day. Car took a beating and handled it like a Queen all day (a hot day too). Coming home, and this time up a different but steep hill, the exact same thing happened again. I let her cool down for about 30 minutes (as she refused to start) and once cool she fired up and I got home.

Have barely driven the car since, but these are the symptons:

- car loses all engine power instantly
- seems to happen after a long drive when car is warm
- only seems to happen when coming up hills
- does not appear to be electrical

It is tough to replicate the failure as it only seems to happen coming up hills. However, the couple of times I have got it to re-occur, I have checked lift and fuel pump and watched fuel pressure gauge. My old man believes it is possibly the fuel pump (current 044 is quite noisy), but as I said, difficult to diagnose as it happens so randomly.

Fuel set up is pretty simple: tank > filter > lift pump > swirl pot > 044.

I have replaced the lift pump and checked the pick-up, but all appear OK. It has done it one more time after a long cruise, whilst driving along the freeway (and not up a hill) and on a relatively cool day. Fortunately though it came back to life after about three seconds and I made it all the way home.

Some people have suggested ECU connection, CAS and fuel pump. Any thoughts are appreciated. Cheers.

Link to comment
https://www.sau.com.au/forums/topic/445982-random-stalling/
Share on other sites

You say it mostly happens on hills so I am thinking its something with the fuel system, maybe the pump is not installed/plumbed up properly and starts sucking up air or dropping pressure.

Is this in an R33, cause I don't think 044's are a direct fitment meaning it may have not been done properly.

Edited by AngryRB
Link to comment
https://www.sau.com.au/forums/topic/445982-random-stalling/#findComment-7347784
Share on other sites

I had similar issues two cars I imported almost 10 years ago. One was due to clutch fan issues, the car basically overheats and shut. Its a common Nissan problem which the Water temp gauge rise no higher then halfway point, so the driver could not be notified in the event of over heating.

Other car with similar issue was due to an lose timing belt, probably skipped few tooth or what not, the issues was resolved after a new belt was installed.

Link to comment
https://www.sau.com.au/forums/topic/445982-random-stalling/#findComment-7348252
Share on other sites

  • 3 weeks later...

Im having almost exactly the same issue. My problems started after the car sat idle for a few months while I was overseas.

At first it seemed like it would only occur when running up a hill, but not every hill, just say one in every 50 for example, but it seems like the problem has evolved as it now occurs on any or no incline. This also happens randomly at any speed, and/or anywhere in the rev range.

In the same way as cactus stated, when the car runs, it drives like a dream. But the cutting of power is completely random. Its pretty safe to say that the car will work fine for at least 10 minutes at the start of the day, but anywhere from 10-30mins of driving, at some stage the power will cut. It may just be for a second or two and then continue on, or like what happened on the freeway the other day. Driving at 100, power cut, never came back, rolled to the emergency lane.

Sometimes you can restart the car immediately and continue on your merry way, but what is happening more often now is you have to sit for a few minutes before it will restart. I have a power fc with hand controller, and there is nothing crazing going on when I watch the voltage readings from the AFM. There also no coughing or hesitation of the engine, so its not like the fuel pressure is simply dropping, its almost like the ignition gets cut. My water temp is sitting at around 70º normally, but its not like its spiking at the points of stalling.

The car has had its coilpacks replaced, new spark plugs, cleaned all ignition loom connections, AFM sensor and connector cleaned, fuel filter replaced and a new air filter for good measure. All of which has made zero difference. The car is running the standard fuel pump, but I do have a spare 040 kicking around that I will swap when I get the chance, but like I said it before the power loss is to instantaneous, seeming more like its on the electrical side of things.

I'm really hoping someone can shed some light on this as its becoming quite an inconvenience.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/445982-random-stalling/#findComment-7363867
Share on other sites

Ive had similar issue with an rb30et

It started as a random miss every few drives, usually happened when hot/in traffic.

I assumed it was a failing coil, due to hot conditions etc.

But after a coil change and no fix!

It then evolved into a random engine stopping like yours, it would be 100% good then just like it was turned off, come to a stop, wait a few mins then all ok again, no fault codes either.

Then one day it just failed to start, followed by cas fault code.

Replaced the cas, never faulted again.

Link to comment
https://www.sau.com.au/forums/topic/445982-random-stalling/#findComment-7363956
Share on other sites

  • 3 months later...
  • 2 months later...
  • 3 weeks later...

Hi had a similar problem with my rb30 powered vk commodore like you I replaced the afm and it fixed it for about 6 months and it happened again so I tried a afm from my mate and away it went perfect until I changed it back I fornd I had to restrict the return fuel line to the tank and it ran perfectly again I ended up fitting a tomei external fuel regulator to the vehical witht the same afm and that was about 5 years ago and never had a problem since and im still using the same afm.

Link to comment
https://www.sau.com.au/forums/topic/445982-random-stalling/#findComment-7487053
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi. A little bit of an update. It maybe(hope not) looks like i would need a new tranny(it would be "maybe" a cheaper or better option anyway) So i need some info. I know i need a different propshaft(i can make custom one) LSD is not a problem cuz the engine will be still(for now) N/A RB20. So if i buy RB25DET NEO tranny...is there something else i need? I read something about push/pull type but i do not know if i need to "change" something or i can just plug n play onto my engine a go? Thanks for the advice  
    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
×
×
  • Create New...