Jump to content
SAU Community

Recommended Posts

On offer is a 3000km old re401a 4 speed box built and supplied by gzm automotive with all the upgrades. Comes complete with all wiring, b&m quick shifter, 3500rpm stall converter, Flex plate, external cooler and drive shaft to suit skyline r33. box will bolt up to rb30 block. I was running it in a r33 with 30/25 combo for a very short time with only 240kw/atw. In as new condition. Built to handle over 350kw/atw. I payed over $4500 for the setup going for a fraction of the price! It is a full manulised auto with 4th gear on a switch, was the other option to a C4 setup for $9000.

Asking $3000

I also have the complete motor I was running but was pulled out due to blown bottom end...

Will strip sell in parts or complete.

25/30 combo with...

Nistune ecu (was just tuned with reciepts $750)

Less than 10k old twin garret gt2560r turbos with manifold to fit rb25 head ($2600 worth with polished rb26 intake)

Complete exhaust including dump pipes (mostly stainless) and custom 02 sensors with inovate lc1 to suit.

All pipe work including fmic, bov and z32 afm.

Rb25 head complete with adjustable cam gear etc.

Blown forged rb30 bottom with less then 20k pistons may be ok but im uncertain.

Custom plenum, fuel rail with 550cc injectors. 65mm Throttle body, catch can, few other bits and pieces.

Asking $4000 for the motor with all bolt ons or make offers on parts seperatly.

Located penrith nsw

On offer is a 3000km old re401a 4 speed box built and supplied by gzm automotive with all the upgrades. Comes complete with all wiring, b&m quick shifter, 3500rpm stall converter, Flex plate, external cooler and drive shaft to suit skyline r33. box will bolt up to rb30 block. I was running it in a r33 with 30/25 combo for a very short time with only 240kw/atw. In as new condition. Built to handle over 350kw/atw. I payed over $4500 for the setup going for a fraction of the price! It is a full manulised auto with 4th gear on a switch, was the other option to a C4 setup for $9000.

Asking $3000

I also have the complete motor I was running but was pulled out due to blown bottom end...

Will strip sell in parts or complete.

25/30 combo with...

Nistune ecu (was just tuned with reciepts $750)

Less than 10k old twin garret gt2560r turbos with manifold to fit rb25 head ($2600 worth with polished rb26 intake)

Complete exhaust including dump pipes (mostly stainless) and custom 02 sensors with inovate lc1 to suit.

All pipe work including fmic, bov and z32 afm.

Rb25 head complete with adjustable cam gear etc.

Blown forged rb30 bottom with less then 20k pistons may be ok but im uncertain.

Custom plenum, fuel rail with 550cc injectors. 65mm Throttle body, catch can, few other bits and pieces.

Asking $4000 for the motor with all bolt ons or make offers on parts seperatly.

Located penrith nsw

WILL TAKE OFFERS!

Stripped motor down last night. Block destroyed, cylinder 2 rod through the side and piston damage. (unfortunate as was a forged setup) head untouched.

So only the top end complete rb25 twin turbo setup, with vgc head around 20k on head only.

Exhaust is a full stainless 1 piece.

Full setup with everything to convert Rb25 or rb30 to a twin turbo.

Including ARP stud kit

cometic head gasket

Braided turbo lines with all fittings

also have a Greddy electronic boost controller

Asking $2500 but too big too post located Penrith NSW.

At this stage would like to try sell it as a complete setup, if it's not gone in a week I will look at separating it all and listing prices and pics of each item.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • In a few years from now, you'll regret that. It'll eat away at you, knowing the truth of the ugly hiding beneath the beautiful exterior... 😛
    • I don't think the G2 profile is particularly dangerous for the engine per se, more just are you actually ok with the turbo lag trade-offs? If the answer is yes then go for it. I personally don't think I'd be ok with it because I spend so much time at lower RPMs and I really enjoy the feeling of being able to stay in 5th gear on the highway and just roll into the throttle to get boost. Or staying in 3rd gear on "gentle canyon cruises" without feeling the turbo lag too badly. The 525 pump should be able to run flat out on factory lines but I would bet the pressure drop from pump to regulator is quite impressive. I don't know how much it would be exactly but I've seen figures like 30 psi thrown around.
    • It's interesting seeing everyone talk about what level of risk they are happy to tolerate.  Building a GTR always has a level of risk, you could be that lucky guy that drops 20k on the engine build alone and still has the thing go pop on the dyno. Life is fun like that.  The way I see it, the thing is a toy to be enjoyed. I'd be happy to turn up the power on stock motor and limit the risk with sensible tuning and engine protection. If it still goes pop, it is what it is. The car isn't a daily driver so it can happily sit while a plan is made to sort it out.  Given this thing will be a street car only, I really feel it's worth the (relatively small if managed well) risk to turn the power up to around 350KW on e85.  I don't think anyone getting into the skyline game now is doing it out of logic. Surely it is a purely emotional decision so I'm not sure how important it is to think about the engine build logically. The heart wants what it wants.  @joshuaho96 little note for Josh, I run my 525 pump flat out all the time and through the factory lines without any issues. (excluding the melting connectors, that's sorted now. we'll pretend it never happened lol)
    • But the Nexus S3 is very expensive and won't be as purpose-built for the application as a separate electronic boost controller :^) More seriously my pet issue here would be that the Walbro 525 running at 100% duty cycle is going to require more FPR than the stock setup can handle. I'm also pretty sure from what I've seen elsewhere you might want to slow down the pump regardless unless you're going to come up with some way of upsizing the fuel lines coming from the fuel tank. Factory 8mm fuel line doesn't actually flow very much if you want to keep pressure drop down between the fuel pump outlet and FPR. If you really want to "keep it simple" I would run only as much pump as you need and source a fuel pump controller to slow down the pump in the vain hope of being able to run stock-style FPRs which are pretty dinky. Or just use the HICAS lines and it should be mostly fine. OP should also really think hard about what profile they'd want out of the turbo. My pet choice here would be the G1 profile rather than anything higher power but YMMV. I already think ~stock turbo lag is pretty bad so I don't want to make it worse. In "gentle canyon cruising" I found that I spent a lot of time around 4-4.5k RPM. I also recommend DIYing labor if you're detail-oriented enough. Costs are high for labor + if you do it yourself you can be your own quality control.
    • GTSBoy is again on the money. My actual advice? Sell the car. (really). For what it's worth as is, you can sidegrade into something much better. If you care about function then this is the actual move. If you want a Skyline to perform, set aside about $100K to do it. This is NOT a typo. You will see right away these are two very different mindsets. Realistically we're talking full restomod for any Skyline still kicking around. Have an honest think about which one you are.. and what you want to do, and how much you want to invest in this (with no return).
×
×
  • Create New...