Jump to content
SAU Community

Recommended Posts

spanner? you need a 1/4" socket set.. spanner will hit the fan and/or the ancillaries belts I think.. never tried loosening the CAS bolts with a spanner, curious now if it fits lol.. always have used a socket

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7366069
Share on other sites

All done and didnt break the circlip. Im not a mechanics butthole but all went well and pretty straight forward. Ended up with 11-12lb boost heaps better to drive.

Next job is the new heater core i picked up. Not looking forward to that.

Then in 2 weeks going in for a tune. once i pick up the z32 ecu.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7372687
Share on other sites

  • 1 month later...

Ok bit of progress and wondering where to go next. Got the ecu and nisstune and tuned and what a difference got 207 kw at the wheels which i thought was pretty good off a stock turbo, motor, injectors and fuel pump. Now what next to do. Im thinking afm, injectors and fuel pump. No idea on what type yet some research will have to happen

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7398688
Share on other sites

to be honest mate, you can't go much further without spending heaps and losing response anyway.

But if you want more power and I assume you do, next job would be new turbo. The stock turbo will die an early death if you push it any harder

supporting mods include but are not limited to:

-fuel pump Walbro GSS341/342 for petrol or F90000267 for E85

-Z32 AFM

-Injectors (if you want more than ~245rwkw on petrol or if you want E85 at all)

-coilpacks/clutch if need be.

Don't forget to run a direct battery feed for a new fuel pump regardless of which model you use.

Good luck

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7398705
Share on other sites

would i be able to reach 250kw with the stock turbo.

Absolutely not. Maybe on E85 you could get close, but it will be a bad thing to do. Turbo maxes out at less than this in terms of air flow, and when you push it that hard you are risking it flying to pieces (fragile ceramic turbine remember!!!!!!!!)

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7398746
Share on other sites

Absolutely not. Maybe on E85 you could get close, but it will be a bad thing to do. Turbo maxes out at less than this in terms of air flow, and when you push it that hard you are risking it flying to pieces (fragile ceramic turbine remember!!!!!!!!)

Cheers mate will probably go high flow turbo so boost comes on early unless there is an after market turbo that can do this and handle high teens off boost. Will get the fuel pump probably this week if i have time and then in a few months the rest and possible turbo

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7398759
Share on other sites

Look at http://www.sau.com.au/forums/topic/448435-factory-response-aftermarket-turbo-rb25/?view=findpost&p=7394103 to see what an HG highflow can do for you even with stock injectors. The ability to wind the boost up to values that will destroy the stocker is not to be scoffed at.

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/page/3/#findComment-7398771
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah it is really until until you get a feel for it....then it is easy. Which is no use to you really. I'd buy that torque wrench. One thing from sure, many (most?) tyre shots overtighten the f**k out of wheel nuts, so don't worry if they were tighter when you tried to take them off compared to when you do them up. I've had some crazy tight ones come back from shops, quite apart from the potential damage to the thread, I can't see a smaller person taking the wheel off on the side of the road
    • Hey mate, thread dredging hahah To answer you directly, yes I had my itbs oversized and custom butterflies etc made by EFI Hardware in Sydney back around 2017-2018 if memory serves. My setup had a vast amount of other changes too though, so no direct comparisons unfortunately. i went from oem itbs, HPI manifold and internal gate hks 2835 pro S; to 49mm itbs, cnc port matched Nismo plenum, RB25 Neo lower runner adapter hand port matched, r31house v2 Takoashi MAX equal length twin scroll manifold with twin 38mm tial gates and a FP HTA3076 with 1.01ar twin scroll real hosing. feom power Fc to a link fury wired by 12volt, r32 gtr fuel tank conversion with frenchys twin 460 / surge tabk fuel hanger combo kit, 1659cc injectors, full 4 inch turbo back stainless exhaust, Z34 6 speed, Tomei 2way with 4.3 final drive and a ton of other shit. ive posted elsewhere here with complete run down, but here's a graph from its initial tune with no boost control on, 20psi gate springs only and e85.   7542AE72-DA92-4E0B-8660-B0940FEA7F24.mov
    • On sale mate, $55. Sorted. https://www.supercheapauto.com.au/p/toolpro-toolpro-torque-wrench-1-2-drive/565734.html?utm_content=paidsearch-pmax&gad_source=1&gclid=Cj0KCQjwytS-BhCKARIsAMGJyzqYEnwWmhWf6gxTST_Nz06Gd2VePgyvL7lh6PWrQtbjXTsI6TqSCLEaAuaCEALw_wcB&gclsrc=aw.ds
    • Slap it and say it ain't going no where, you'll be fine.
    • So the whole rb25de neo setup was a tiptronic setup and i swapped everything over to my rb20de neo setup and yes even the cluster of the rb25 was swapped over. 
×
×
  • Create New...