Jump to content
SAU Community

Recommended Posts

  • Replies 122
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Thats still one hell of a figure though - 395AWKW subtract 25 = 370 AWKW on roller dyno - Ide be suprised if GTSS (on pump fuel) made that type of power.

We dynoed the car with Singapore's pumped V-power. 100RON as told by the tuner. Btw that power is obtained by almost maxing out 680cc injectors. Of course it's not gonna run on that boost everyday with the stock rods. :wassup:

We have roller dynos here but they all give different results. I was told by the dyno operator that various factors can affect the results of roller dynos such as how tight the car is strapped down and even the alignment figures. How true was it I don't know. Perhaps someone can explain.

Pictures here.

http://www.skylinesaustralia.com/photopost...500&ppuser=7538

  • 1 month later...

did anyone take notice of MrNismo's engine specs?

The cengine is running with the following specs:

- 264 IN/EX cams 10mm lift

- P&P head

- 87mm Forged Pistons

- Standard rods & crank

- F-Con V Pro

note that he has oversized pistons (larger engine capacity), higher duration/lift cams and a modified head which would've contributed greatly to this great power result.

given this, obviously the GT-SS would not make the same power on a standard spec RB26.

Also, as mentioned above, the fuel used was 100RON which allows for more enhanced tuning again over what we have availabel with 98RON (if that) fuels.

Also, fyi has anyone looked at the official HKS website for the power/torque results of an RB26 with GT-SS'?

if you look at the web link below, you will see that they managed to extract 422kw (565bhp) @ 7070rpm and 629Nm of torque @ 5150rpm whilst pushing the turbos to 1.4 kg/cm^2 (~20psi).

these are great results and the power curve looks mighty fat, i am not too sure as to what this would equate to at the rear wheels or all 4 wheels.

http://www.hks-power.co.jp/products/turbo/...ss/ac_gtss.html

oh another thing, please note the mods listed below;

* IN & EX cams - 264 degrees (lift ???)

* HKS F-con V Pro

* HKS Racing Suction intake system

* HKS exhsut, muffler, extensions & front pipe

and in addition;

* 2628cc engine capacity

have a nice day :)

  • 8 months later...

Ok I am dragging this back from the dead!!!

As some of you might know, I have a set of these GT-SS turbos going on the car (today!!!) with the following combo....

rebuilt stock engine

tomei poncom cams 260 260 9.15

greddy split dumps

700cc injectors

RB20 AFMS

apexi FC

blitz SBC spec R

and the usual other bits to go along with it all....

is anyone else running these of late? and if so what sort of boost levels are we talking?

I will post some full specs and dyno reports once it is all done!

does anyone else have any dyno sheets with similar mods?

cheers...

We have already posted up our results of 367AWKW on croydon racing developments dyno dynamics dyno in the motorsport section in the post of 11.7sec with GT-ss turbo's.

These are great turbo's and they make good power.

We make 332awkw with out quiet trust exhaust.

and 367awkw with our straight through 4''.

That is extremely elementary physics and flow dynamics, and I'm sure everyone realises that boost is just a measure of engine resistance to airflow.

start a poll and see how many people really understand even elementary physics and flow dynamics! I did physics at uni years ago, but bugger if i can remember it now!

I like Sk's explanations, and i think its good to get things explained in a back-to-basics way, especially when there is so much misconception about boost, power and efficiency floating around.

Usually the first question people ask me on the street about my car is "How much boost is it running!!?" I think that sums up the main misconception about turbo systems!!!

That is extremely elementary physics and flow dynamics, and I'm sure everyone realises that boost is just a measure of engine resistance to airflow.

start a poll and see how many people really understand even elementary physics and flow dynamics! I did physics at uni years ago, but bugger if i can remember it now!

I like Sk's explanations, and i think its good to get things explained in a back-to-basics way, especially when there is so much misconception about boost, power and efficiency floating around.

Usually the first question people ask me on the street about my car is "How much boost is it running!!?" I think that sums up the main misconception about turbo systems!!!

a bit off track, but i dont want SK to get discouraged!

What spec turbine / compressor and housings do these use , I searched HKS but could not find them

Cheers  A .

which site did u go to dude?

i usually go to either of these below for all HKS references;

http://www.hksusa.com

or

http://www.hks-power.co.jp

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • PRICE  : $1400 LOCATION   : NSW Central Coast FIT  :  All Nissan 350Z type Z33 and Infinity G35 Coupe. See delivery note. Hi, brand new, unused, still in the box.  ($1850.00 is what i paid ) My bad luck !!! I thought my right front  Bilstein was cactus so i bought the ST 's to replace all.  Turns out the right front is fine ( loose mounting after service  by a well known importer of Bilsteins ) So im selling the ST's. They are made by KW ( no intro needed ) . Iam on the Central Coast and im willing to meet up in Sydney metro, within reason and Newcastle.
    • Yep, yeah would need to do the flywheel although the 6 bolt NA clutch can handle a 20de if just wants to replace the stocker.
    • No it's fine. Heat sleeve is a thing. With oil running through it it is unlikely. Engine off heat soak can be a thing though. There is no way that you have a leak through the hose. That has pressure behind it and any small hole will turn into a large one in very short order. It is so much more likely to be leaking from the connection.
    • Really? That's piss weak. I didn't know they hobbled the shitboxen that badly. OK. So probs need to buy a flywheel too. But that's not too bad.
    • Hi all. I already posted some newbie-ish questions here and there but this will be my first "big" post. Last summer I went and fulfilled a kind of childhood wish, because I just thought I needed this experience in my life no matter what. The car I bought is a mildly modded 1995 BCNR33 Vspec. It was repainted to a metallic orange color all around and it had all windows reseated. Not so well done black respray in the trunk and a metallic black in the engine bay. From outside it looks very nice except for a minor paint error on the roof and the rear spats needing new adhesive tape. The inside is pretty clean and no broken plastics, missing or faded buttons. Even the adjustable mirrors and trunk antenna work like a charm. Despite a moderately long list of issues I don't (yet) regret buying this car. Most mechanical problems are just due to age, like worn rubbers here and there. The underside sadly has lots of corrosion, especially to the back. It looks like it either has been driven in the winter for a while or it lived near the saltwater in Japan, the rust is nothing terrible but it'll require to be looked after. Mostly panel gaps and all the mounted components underneath are a bit crusty, but I don't think anywhere has progressed so badly that there's going to be holes. Front right jacking rail is crushed and needs some care so it doesn't develop into a rust crater at some point. Worst part is definitely the strut towers. I thought they looked fine but after taking off the strut bar I noticed that it actually started bulging up on the passenger side. Probably would have passed on the car or negotiated down by some thousand Euros more if I had noticed this before buying, but here we are. Trunk area also has signs that there was a water leak to the interior once but nothing too crazy, I guess lots of Skylines had this at some point. As for the list of (known) issues, I'll try to make this compact. I hope the coloring is self explanatory. Mechanical: -Various busted or soon-to-be busted rubber bushings and ball joints. Will replace ball joints with OEM or better and bushings with polyurethane where possible. -Shaking steering wheel at above 80kph -downshift from 5th to 4th is a bit crunchy unless I rev-match, might just try to renew the shifter assembly, but it's not a priority issue -tailshaft centre bearing could use a replacement, is it worth going 1-piece tailshaft as it doesn't look too fresh all around? Chassis: -underbody corrosion on many spots and in hollow spaces, needs to be treated -corrosion on many bolts, hoses, lines, suspension components, subframes, will be treated when replacing of the bushings is needed as time goes on -strut tower top panels and some of the surrounding panels are rusty, so needs fixing. Will look into doing this with a buddy in the winter, otherwise bite the bullet and pay a professional -driver side door is misaligned to the body and needs to go a slight bit more inwards -both door windows are misaligned and have an airgap where the window meets the door at the B pillar -The Aerocatch latches for the bonnet have locks but no keys, need new keys. -driver side door window is kind of gritty and could use a polish -damaged jacking rails and front frame rails, from people lifting the car the wrong way, might have this fixed by a bodyshop Electrical: -Nismo tachometer is just bouncing and displaying nonsense, supposedly worked fine when the stock ECU was still in the car -An old Greddy boost controller sits on the dash which will be removed as it servers no purpose anymore. -a led segment rpm gauge is on the steering column, will probably also be (re-)moved once the Nismo tacho is working correctly -there was an attempt to make the sound system better by the previous owner but it was just inducing noise all the time, ripped out the amp and filters in the back, no music for now -trunk antenna goes up as long as the radio is on regardless of the mode, I want it to only rise if I choose Radio specifically or per switch -3rd brake light is a bit dimmer than the taillights but everything was converted to LEDs so mabye now it just seems dimmer? -reverse light flickers, have to test if that behavior changes when I fiddle with the gear stick. Hope I can get around changing the switch. -Left side taillight, blinker section has minor water intake and is humid after washing. Other side has a hole in it, probably for that exact reason. I'll probably reseal them entirely and plug the holes. Engine: -minor coolant drips on one or the other hose -rear turbo leaks oil onto the exhaust making the car essentially undriveable due to fire hazard -Oil filter relocation kit has an oil drip at the Dash lines, will probably make a new connection there and tighten real good and pray -throttle body assembly is slightly stuck for the first throttle pedal input after sitting for a while I'm always open to suggestions and advice from more experienced people, I'm sure half of this list is easily dealt with and just requires some time and effort to sort out properly. Once I have some proper pictures of the car I will post some in this thread, I just have to remember to take some more once I get the chance to. Will post updates when I have news on anything, I want to try to keep this thread as kind of a logbook as well. Ultimately my goal for this car is to just enjoy it. An engine rebuild is probably going to happen sometime as well, because it is old after all. It will never be fully new again, I am just not that rich. But I want it to look good, work well and not rot away while I drive it. I'm probably gonna spend a lot of money on this journey, hopefully not an unreasonable amount.
×
×
  • Create New...