Jump to content
SAU Community

My Hearse - M35 Build - Adaptronic

Brick

By Brick,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 73
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Brick
Brick

I found it easier to install by flipping the car upside down. No idea why the picture is upside down. Shows up the right way on my phone and everything else

Footo
Footo

Black ARX!! But then i would go "full tard" and end up like craig (jetwreck) haha

Brick
Brick

Figured now that I have my car all tuned I would show it off a bit and fill in any further mods in the one thread So the facts and figures are 2002 M35 RS four 250T Black Full factory Aero kit B

Posted Images

Brick Mentor

Brick

Posted
  • Author
Posted

Even though a trans cooler is a must have, are you sure the shifting issue was due to trans heat and not an issue caused by the ecu change?

Very confident. I haven't had this issue at all on the street. Also the three runs where i let the car fully cool down I didn't have the issue, the three times i kept the car warm it had the issue.

  • 2 weeks later...
  • 1 month later...
Brick Mentor

Brick

Posted
  • Author
Posted

Fitted up my r34 gtt brakes today. Also painted the rears black to match the front. While I was at it I changed my oil, diff oil front and rear and transfer case fluid.

For those playing at home I fitted QFM HPX pads front and rear

Nice productive day.

post-96472-0-54213800-1414825059_thumb.jpgpost-96472-0-61576500-1414825013_thumb.jpgpost-96472-0-55418600-1414824891_thumb.jpg

  • 2 weeks later...
Hertz Donut Proficient

Hertz Donut

Posted
Posted

Man I need some 18s. It's such a subtle upgrade but makes the wheels look the right size. I found a decent chunk out of one of my 17s yesterday and pointed it out to my wife, who subsequently claimed responsibility. Time to angle for a Christmas present...

  • Like 1
  • 4 months later...
Brick Mentor

Brick

Posted
  • Author
Posted

Installed my nismo dash today.. instantly went from 105k to 180k. Also noticed missing screws holding the dash in, no guessing needed as to why... I wonder how many ks it really has

post-96472-14282791936371_thumb.jpg

  • Like 2
zoomzoom Mentor

zoomzoom

Posted
Posted

That's a crowded dash! If I had more time I would like to mess around with microcontrollers and the serial output on the adaptronic. Then you could integrate another digital display somewhere on the dash, instead of old school gauges.

  • Like 1
Brick Mentor

Brick

Posted
  • Author
Posted

That's a crowded dash! If I had more time I would like to mess around with microcontrollers and the serial output on the adaptronic. Then you could integrate another digital display somewhere on the dash, instead of old school gauges.

There are digital race dashes that plug straight into the adaptronic, I just have many things that are higher priority with my funds. I do plan on moving those gauges one day.

  • 2 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By TurboTapin · Posted

      Do the following first and get back to us. - Clean and verify your IACV - Verify for vacuum leaks/post MAF leaks. (Pressure test is the best and cheapest way) - Do you have a BOV with stock ecu/MAF? If so, remove it.     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      Hey all, The skyline I have is stalling when the engine is at normal operating temp.  When starting it while it is cold, it'll run just fine.  I have replaced the battery (bad cell), I have replaced the fuel pump, fuel filter and clean the MAF sensor.  Any other suggestions?
    • DRoc81
      Shifting questions

      By DRoc81 · Posted

      Thanks for all the information on this.  I tried ordering the parts from Amayama website and all 3 Solenoids are discontinued and not available.  Does anyone have any other websites to suggest that I could find the parts?   Separate issue-- I will start a new thread, but basically the vehicle is stalling when warmed up.
    • TurboTapin
      RB25DET Solid lifter conversion

      By TurboTapin · Posted

      It's unfortunate what Tomei USA has done to Tomei's name in general. I'm very weary of ordering parts from them now. I only order direct from a Japanse source (e.g Nengun). At least their logos are different, so you end up knowing what you have. 
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Update Issues 5 (plus #4) - 10 After making a claim about issue #4's missing part, DeAgostini Japan sent a whole new issue #4 and it arrived about 2 weeks after that. That was back in early March. It took another 4 weeks to receive issues 5 - 13 though. This update is for issues 5 - 10. Ove the 5 issues the front left suspension and most of the engine have been completed. The quality of the castings and fit of the parts is quite good, it seems better than DeAgostini's BNR34 Skyline GT-R from the Fast & Furious 2 movie, which (to me anyway) doesn't seem to have as tight tolerances or quite as accurate castings.  Each issue has a lot of info about the 1989 - 1993 Skyline range and other Nissan models from that era, but the focus is on the BNR32 Skyline GT-R Nismo and the various racing it did in Japan, Europe (Spa 24hrs) and of course Australia. I've included some text translated with Google Lens in some photos and will add to them if there's anything worth including. 
×
×
  • Create New...