Jump to content
SAU Community

Recommended Posts

Is there a link to a detailed thread on the attessa system in the nm35s?

My thinking was its pretty much rwd untill the system senses traction being lost and activates the fwd.

After reading about the rpm diffrence between the break sensor mod while on the stop and go pedals, i wanted to check. Sure enough sat on about 2500rpm as suggested.

Though i did notice small tyre witness marks on the driveway, so tried again the next day with the "Sync" switched on and held it a little longer to be sure, again twin marks.

I would have though the attessa would have not allowed that to happen? Also, i have taken off quckly on loose gravel had had the back spin and step out slightly.

So any more info on the attessa side of things (other then wikkipedia) would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/447319-attessa-question/
Share on other sites

Is there a link to a detailed thread on the attessa system in the nm35s?

My thinking was its pretty much rwd untill the system senses traction being lost and activates the fwd.

After reading about the rpm diffrence between the break sensor mod while on the stop and go pedals, i wanted to check. Sure enough sat on about 2500rpm as suggested.

Though i did notice small tyre witness marks on the driveway, so tried again the next day with the "Sync" switched on and held it a little longer to be sure, again twin marks.

I would have though the attessa would have not allowed that to happen? Also, i have taken off quckly on loose gravel had had the back spin and step out slightly.

So any more info on the attessa side of things (other then wikkipedia) would be greatly appreciated.

If you saw two black lines that would be different. Atessa reaction is not immediate. In fact R32 was quite slow. R33 (and Stagea) is quicker and R34 GTR is quicker still. The answer is in your second sentence - attessa senses traction being lost - it can't somehow anticipate it.

If you saw two black lines that would be different. Atessa reaction is not immediate. In fact R32 was quite slow. R33 (and Stagea) is quicker and R34 GTR is quicker still. The answer is in your second sentence - attessa senses traction being lost - it can't somehow anticipate it.

It does sort of anticipate it, by pushing some drive to the front wheels under hard acceleration, even if there is no slip. The biggest problem with the R32 setup is that its biased much too heavily to the rear. I have a cheapo ebay attessa tweaker in the GTR and it transforms the car. Also R32s also have no preload - ie no drive at all to the front under normal conditions. The R33 and later all send a little drive to the front all the time, which improves response, and is why you need to remove the front driveshaft if you're using a 2WD dyno. In an R32 you can just pull a fuse to use a 2WD dyno.

While we're talking attessa, do NM35s still require flatbed for towing like early attessas?

If you saw two black lines that would be different. Atessa reaction is not immediate. In fact R32 was quite slow. R33 (and Stagea) is quicker and R34 GTR is quicker still. The answer is in your second sentence - attessa senses traction being lost - it can't somehow anticipate it.

It does sort of anticipate it, by pushing some drive to the front wheels under hard acceleration, even if there is no slip. The biggest problem with the R32 setup is that its biased much too heavily to the rear. I have a cheapo ebay attessa tweaker in the GTR and it transforms the car. Also R32s also have no preload - ie no drive at all to the front under normal conditions. The R33 and later all send a little drive to the front all the time, which improves response, and is why you need to remove the front driveshaft if you're using a 2WD dyno. In an R32 you can just pull a fuse to use a 2WD dyno.

While we're talking attessa, do NM35s still require flatbed for towing like early attessas?

I have only ever flatbed towed the car. I wouldn't want to try due to the preload on the transfer case clutch though

I have a feeling the M35 electronic G sensor and Attessa computer is much quicker to respond than the earlier units.

So its more of a case of pecentage of power Vs breaking effect?

If theres a constant percentage of drive being sent to the front and you stand on the break and accelerator, is it just the fact that theres less power and larger breaks up front that allow the rears to turn?

My car breaks traction when my tyres are really cold or when the steep driveway is really wet or the combination and I cannot get up my driveway as the rear wheel is still spinning and I slide back down. This is at a low speed lets say 5km/h? Even with snow mode activated it struggles going up my driveway.

I can launch my car from 3500 or 2500? pissing down rain with the road flooding and not break traction.

My car also leaves chirp like marks when leaving my garage.

But, if going up a steep hill while raining and I floor it, I can feel the rear slip then the car straightens up then I know that attessa has corrected the slip.

  • 2 months later...

FWIW, as well as difference in front vs rear wheel speed from the ABS sensors, and longitudinal G force, they also have a TPS input.

so yep, it's pretty damn good at guessing when you might loose traction.

bloody amazing system for something designed on this

Classic-Games-The-Age-of-DOS-IBM-PC.jpg

FWIW, as well as difference in front vs rear wheel speed from the ABS sensors, and longitudinal G force, they also have a TPS input.

so yep, it's pretty damn good at guessing when you might loose traction.

bloody amazing system for something designed on this

Classic-Games-The-Age-of-DOS-IBM-PC.jpg

Yeah, I've watched my torque split gauge throw drive to the front whilst cornering, and encountering a dip; no loss of traction felt, but it is impressive in it's pre-emptive nature.

A wet road would likely have seen a loss of traction in that combination of conditions.

I have not ran part numbers on the nm35 systems, but from the looks of it they run an r34 pump and clutch packs. The only way to confirm would be to look at the g sensor.

If it is R34 data and programming it takes TPS, G sensor, wheel speed and the map sensor. Calculates over a matrix and runs variable prime pressures.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Price seems pretty good to me. Also seems a hell of a lot cheaper then buying another vehicle that only ever gets used for towing.  I'm a long way from you mate, I'm a couple of hours out of Brizzy. 
    • New [400]Z, they're available in manual and you don't have to worry about parts scarcity. 
    • Just planning to have the wiring neat and hide as much as possible.
    • The sodium acetate, mixed with citric acid, doesn't actually buffer each other. Interestingly though, if you used Sodium Acetate, and acetic acid, THAT becomes a buffer solution. Additionally, a weak acid that can attack a metal, is still a weak acid that can attack a metal. If you don't neutralise it, and wash it off, it's going to be able to keep attacking. It works the same way when battery acid dries, get that stuff somewhere, and then it gets wet, and off it goes again breaking things down. There's a reason why people prefer a weak acid, and it's because they want TIME to be able to be on their side. IE, DIY guys are happy to leave some mild steel in vinegar for 24 hours to get mill scale off. However, if you want to do it chemically in industry, you grab the muriatic acid. If you want to do it quicker at home, go for the acetic acid if you don't want muriatic around. At the end of the day, look at the above thumbnail, as it proves what I said in the earlier post, you can clean that fuel tank up all you want with the solution, but the rust that has now been removed was once the metal of the fuel tank. So how thin in spots is your fuel tank getting? If the magazine on the left, is the actual same magazine as on the right, you'll notice it even introduces more holes... Well, rust removal in general actually does that. The fuel tank isn't very thick. So, I'll state again, look to replace the tank, replace the fuel hanger, and pump, work out how the rust and shit is making it past the fuel filter, and getting into the injectors. That is the real problem. If the fuel filter were doing its job, the injectors wouldn't be blocked.
    • Despite having minimal clothing because of the hot weather right now, I did have rubber gloves and safety glasses on just in-case for most of the time. Yes, I was scrubbing with my gloves on before, but brushing with a brush removes the remaining rust. To neutralize, I was thinking distilled water and baking soda, or do you think that would be overkill?
×
×
  • Create New...