Jump to content
SAU Community

Recommended Posts

Recently I have noticed a increase in the volume of the popping and sometimes cracking noise from my exhaust when I'm de accelerating. What could cause this? The engine is stock with stock intake it has the usual 3.5 inch exhaust with cannon and a high flow cat. I haven't changed anything on the car but have been told that my oil rings could be stuffed. Would the popping noise increase due to worn rings? Also if your turbo is on it's way out, would this increase the pops?

It used to do it when it was over due for a service then when it got serviced it would go away. Anyone have any ideas? I'm stumped.

Link to comment
https://www.sau.com.au/forums/topic/448243-r33-popping-cracking-exhaust-noise/
Share on other sites

Yeh funny you mention it becuase my r33 gtr is completly stock down to the exhaust system and occasionally i get a little poping when de-accelerating, never really crackling but.

how does your car perform with the 3.5 inch exhaust sytem on stock internals? only becuase im about to get a system made up but i was gonna go 3 inch? how loud is your system?

From inside the car it's not that loud. I run the stock manifold with 4 inch dump and 3.5 system, highflow cat and a drager cannon. I have been told that when you get on it it is a tad rumbly from outside :yes::wub::woot:

I was going to put a different cat on it to make it even louder but then you would get that droning noise through the car :down:

Car runs fine. Only draw back is you can't have the car to low because of the zorst. I've been told that it sits higher than most 33's.

Its got to do with your exhaust, now that its opened up and is more free-flowing you should notice a slight increase in boost as the turbo is able to flow more freely, and thats why it pops, because now its "out of tune" but the slightest amount. nothings really going to fix it until you get a tune, i.e. nistune or something.

but as to why it actually pops I just assumed is was unburnt fuel, but I'm no expert, just sharing my knowledge.

sounds legit, becuase i rang castle hill exhaust and the quoted me $950 for a 3'' Mandrel bent (Mild steel/stainless cannon) with 100cell

hi flow cat. you think this would be suitable for my setup or should i go 3.5 for when i do more work? i just dont want the drone like you mentioned and i dont want to loose back pressure :no:

Its got to do with your exhaust, now that its opened up and is more free-flowing you should notice a slight increase in boost as the turbo is able to flow more freely, and thats why it pops, because now its "out of tune" but the slightest amount. nothings really going to fix it until you get a tune, i.e. nistune or something.

but as to why it actually pops I just assumed is was unburnt fuel, but I'm no expert, just sharing my knowledge.

The exhaust was on the car since I bought it :) and it never used to have this popping issue that bad.

sounds legit, becuase i rang castle hill exhaust and the quoted me $950 for a 3'' Mandrel bent (Mild steel/stainless cannon) with 100cell

hi flow cat. you think this would be suitable for my setup or should i go 3.5 for when i do more work? i just dont want the drone like you mentioned and i dont want to loose back pressure :no:

I'd probably go the 3 inch and then get a decent resonator. That should give you the drone your after.

"i dont want to loose back pressure" and "That should give you the drone your after"

Wait, what?

Anyways, its just unburnt fuel. You could double check using a consult cable. Maybe the "closed throttle" signal isn't working properly when you let off the throttle.

You most certainly want to lose back pressure, you have a turbo car + you shouldn't be worrying about scavenging effects. Get a 3.5" exhaust with good mufflers (e.g. Magnaflow), you won't have drone issues then. I run a 5Zigen 3.5" cat back (two mufflers), no drone at all and car went harder. Shame the mid muffler cracked and had to replace it with an inferior muffling Xforce one.

Popping and crackling is unburnt fuel in a hot exhaust. When is the last time you changed the spark plugs?

  • Like 1

If it is the closed throttle signal, how would you check that?

The easiest way I can think of is with a consult cable. You can see the signal in realtime or you can create a log over a period of time, ie going for a drive. I think theyre a must for any skyline etc owner who needs to track down a fault.

I'm going to lock in broken exhaust stud/s.

Documented RB25 issue over time. The release in torque on the manifold could have introduced air into the exhaust on over-run, causing the unburnt fuel to ignite with the extra presence of oxygen.

;)

Huh? :huh::mellow:

Do they snap off over time? Is that what you are saying? Or are you saying that they snap when you change the manifold? If this is happening wouldn't I hear a exhaust leak on the manifold itself?

Yes the studs weaken and snap after many years, especially if yours have not been replaced from the factory.

However mine are new and my car still makes little pops and burbles on the overrun. Was particularly noticeable after fitting a new 3 inch exhaust. If you don't notice any issues with fuel consumption I wouldn't be too concerned.

I'm going to lock in broken exhaust stud/s.

Documented RB25 issue over time. The release in torque on the manifold could have introduced air into the exhaust on over-run, causing the unburnt fuel to ignite with the extra presence of oxygen.

;)

Now that you mention it, my Skyline used to pop on decel even with a standard exhaust. Since replacing the manifold with one without a crack it doesn't pop any more!

I don't doubt that 3inch exhausts pops and carry on at all, but none of that explains why the popping has actually increased over time with no other mods.

You might not hear the exhaust leak on throttle over the exhaust, or it may be a very small leak.

It's just my theory, take it or leave it ;)

Nothing to be all that worried about anyway.

I guess it could be any gasket on the exhaust side too, by this logic.

Now that you mention it, my Skyline used to pop on decel even with a standard exhaust. Since replacing the manifold with one without a crack it doesn't pop any more!

Now that you've mentioned it, my rear turbo gasket started leaking. I had some good pops.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hey all, my 2004 Nissan Skyline 350GT overheated the other day with coolant boiling and leaking out of the coolant reservoir when I was parking. So today, I started it up again just to see if it was a thermostat/head gasket issue. After about 20 mins of running, temps were normal again, no coolant was leaking out and the upper reservoir hose was warm but my engine suddenly cut off. I checked the oil dipstick and cap when it was running and there was no white foamy residue and the exhaust did not have white smoke. I tried starting up the car again but it would only crank, similar to when I had a camshaft sensor issue just that now there’s no check engine light on the dash. Any ideas? Unfortunately I don’t have an OBD2 that can read the Nissan's programme.
    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
×
×
  • Create New...