Jump to content
SAU Community

Recommended Posts

as some of u know my car was stolin and strip of her engine cooler and ecu leaving me with not much at all well well well the *** wits where cought trying to sell off my gear over the net and in the trading post my freinds told me about it so i checked it out told the police about it and they arange for me and a copper to go and have alook as this stuff as we where keen byers ha ha ha ha when we met this person we asked him what dose have he said hear have a look as we did and boom :D i saw it there my front mount cooler nismo my ecu motec and my poor baby rb26 been pulled down to little bits :) just wanted to kill him then the copper pulled out his bage and busted the wanker as we found out there were 4 of them who go around and target performence cars and pull them up on tow truck and strip them and dump the bodie well KARMA people u just got to belive in it thats for sure whats goes around comes around they lived on spring vale road spring vale and they where lebs not to say all people are bad or anything just stateing who they where ? well im glad and thought goes out to any one please be carefull whee u park your car i might be very lucky hear as it is very very hard to get your things back in this case im just have good mates who look out for me

Link to comment
https://www.sau.com.au/forums/topic/44839-the-fools-where-found/
Share on other sites

It is such a relief to know someone out there has had a win with car thief's , does not happen very often . Hope the coppa's up here have as much luck , as there has been a sh!t load of cars stolen up here of late.

did they find the $4,000 VSPEC II NISMO EDITION Engine  that you sold ? but you said its yours now! weird. caught in a lie.

your so funny man, your full of crap.

EDIT : i thought they tought English in Yr-7 ? i geuss 2 years of it isnt enuf...youll get stuck in VCE dont worry.

Did they try to offload it on ebay too? their accounts should be banned by now considering now that they're arrested, you may want to notify ebay if you haven't...

Glad to hear you recovered the bits and arrested the scums... can you put everything back into the car to make it all sweet again?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bump on this to not make another post, had a ‘head drain’ leak on me and have the engine out as we speak. Planning on just putting a new freeze plug back in , plug the tapped holes and just be done with that headache.    Now I still want to relieve pressure to allow oil to pass down the blocks returns easier. I’ve seen catch cans with multiple vents help folks with this issue on this forum.  I’m wanting to make my own. I have some pictures here of my setup if anyone can help how I should plumb and design the catch can I would deeply appreciate it !   rb25 Oil upgrades: 1.0mm restrictor n1 pump/billet gears extended crank collar  extended sump with trap doors/w welded fitting    
    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
×
×
  • Create New...