Jump to content
SAU Community

Gt30 .63 Or Gt35 .63?

hairdryer33

By hairdryer33,
in Engines & Forced Induction

 Share

Recommended Posts

Blackkers Experienced

Blackkers

Posted
Posted (edited)

38mm will be fine so long as you plan to run a decent amount of boost.

low boost + big turbo needs a bigger gate

GT35 size turbos don't really belong on a RB25 street car. a .63 rear on a GT35 turbo is a mismatch. Too much compressor, too little turbine.

GT30 with a 0.63 rear housing would be nice on the street but 0.82 will give you better top end and a few more usable top end revs.

You could always go GT30 with .63 rear and E85 + 22-24psi externally gated for around 330+ rwkw peak. usable boost would come on just before 4000 probably. That would be a mean street car

Edited by Blackkers
scotty nm35 Grand Master

scotty nm35

Posted
Posted

I agree, you can get away with a 38mm if the flow into it is optimised. Just welding it on a 90 won't cut it.

There is perhaps 200 rpm between the housings, there are also other housing options if you are going external gate. The Taiwanese stainless Tial knock offs are pretty good from my testing, and Kinugawa make some good ones in various sizes.

GTScotT Grand Master

GTScotT

Posted
Posted

The kando 10cm is 1/3 of the price and gives you an inbetween size (.7x)

I've used the kando 12cm (.89) on a GT30 core and so far have found zero drawbacks. I have also seen a few in action and results indicated they did exactly what the specs implied.

Far better value in total if you buy a garrett CHRA and kando housing separately.

Ben C34 Grand Master

Ben C34

Posted
Posted (edited)

I've got a brand new kando gt30 12cm for sale at the moment with Vband. You should use thar ;) 150 delivered.

Also have 3076 but with internal gate .82. Don't want to seperate it.

Edited by Ben C34

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • joshuaho96
      Potential MAP Reference Point

      By joshuaho96 · Posted

      Isn't there a fitting on the back of the balance tube? That's what the OEM boost gauge uses.
    • GTSBoy
      Potential MAP Reference Point

      By GTSBoy · Posted

      Getting a decent signal from all 6 throats is a challenge. I don't know for sure, but I suspect that the stock balance tube is not ideal for it. I have done it on an ALFA 4 cylinder (about 35 years ago, so don't ask for too many details). We drilled 4x holes in the manifold runners, put in some fittings and ran hoses to a decent sized (I think it was about 20mm diameter) pipe that ran the length of the inlet manifold. So, it was quite a decent volume. There is a "tuning" balance to be found between the volume of the common plenum on such a thing and the diameter of the pipes running from it to the runners. You need the volume to be large enough to damp out the sharp spikes in pressure signal you get as each runner gets sucked on by its cylinder, but not so large that it becomes too slow to respond to actual changes in MAP. And you need the hoses to be small enough to transmit the signal quickly, but not so small that they delay the signal. You might have to have more than one go at it, if there isn't any actual success based wisdom to be had here. Hopefully there is. Anyway, I would not do it on only a couple of cylinders. I would also not care about "permanently modifying a part". Just bloody drill holes and make stuff better. There is nothing sacred about any GTR unless it is a genuine museum piece that you shouldn't be modifying at all anyway.
    • MBS206
      NC MX5

      By MBS206 · Posted

      He's still joining you, he's just delayed it and won't have the fulleh sick ITBs...
    • Kinkstaah
      R34 GTT front hood lip

      By Kinkstaah · Posted

      The strange thing is this is a URAS front bumper (or clone of it). The bumper actually does not sit flush with the GTT hood - You need the addon to make the hood 'long' enough to reach the bumper. I have no idea why they didn't incorporate this piece into the bumper itself.. instead of sticking it to the hood instead.
    • AdiR34
      R34 GTT front hood lip

      By AdiR34 · Posted

      Another thought on this OLD topic: When you paint your bonnet lip, leave a small unpainted back lip/line along the back of the lip, where it rests on the bumper. That way, the line in the back is much more prominent than the gaps in the front/under the lip - and it breaks the hood-to-bumper connection at the "correct" place, when comparing to a GTR. I'm gonna do this with mine this week, so stay tuned for pics!
×
×
  • Create New...