Jump to content
SAU Community

Recommended Posts

Hey,

I should start off by saying that I am looking at maybe getting a V36. I wanted to ask any V36 owners out there, who have been on a dyno how much power you guys are making?

And if any one has done any modifications ( catback exhaust, intake etc) or tuning (UpRev), how much difference did it make?

I apologise in advance if there is already a thread like this, please post a link to the thread if possible

Thankyou

Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/
Share on other sites

^^^

I bought my auto V35 350GT coupe from a specialist importer. Compared to all the others I test drove, mine seems to have a noticeable advantage in acceleration over the others.

The car was auction grade 4, other than a grounding kit, tein coilovers with EDFC and the factory powerduct (with K&N panel filter), the car is stock. There seems to be very touchy throttle response, particularly at low rpm. I cannot find out what could be generating the extra power! The dealer seemed to think it was chipped. I checked behind the passengers side panel, and the ECU is stock. Would there be any other way to see if it is chipped?

A friend seems to think it may even have upgraded cams- apparently this is pretty common in Japan as it gives them a bit more low down power and torque.

By comparison, I drove one (not from the importer, but someone who was selling privately) with a kinetix plenum, stillen induction and performance exhaust, and I think mine would leave it in the dust.

I haven't done a standing 0-100 yet, nor had it dyno tested.

Edited by camr33
Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/#findComment-7409573
Share on other sites

Yeah I did a bit of research into grounding kits, and apparently they do wonders, particularly for autos. The thread I found was for a us website, I think it was g35driver.com

Someone asked if they actually do anything and the responses were all overwhelmingly positive.

Still, great car, ant it'll run rings around my old R34

Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/#findComment-7409711
Share on other sites

I'm still yet know a person who has installed a grounding kit and had any impact outside auto shift firmness and placebo.

Placebo is a very powerful thing.. I read many many posts about people claiming Strut tower braces had 'significantly reduced' bodyroll. which a STB cannot possibly do.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/#findComment-7409900
Share on other sites

Grounding kits work for auto boxes due to the bad factory grounding. It helps shift smoother and abit harder. Another thing I noticed was my audio got a tad louder. The guys down at the audio shop said it was the grounding that made it better. Who knows...As to gaining kW....I doubt it.

I dont think it makes it look messy....then again I made sure I hid the wires where I could...looks pretty much stock.

Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/#findComment-7409988
Share on other sites

I wouldn't say its in my head, as I didn't know it had a grounding kit until after I bought it.

But it definitely had a definite power advantage over the others I drove, like I said- is there a way I can tell if it is chipped or has aftermarket cams

Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/#findComment-7410009
Share on other sites

I think the general sentament is the difference is not the grounding kit. something else has been done to it.. possibly a throttle controller installed which has changed the throttle body response vs pedal position. Could also have had a uprev tune, which uses the stock ECU.

Grounding kits will normally only help if you factory grounds are very poorly designed, or corroded/damaged. The extra grounding from the transmission casing to the engine/battery may help as the auto solenoids probably ground to the transmission casing, and the existing grounds are a source of voltage drop.

Did it accelerate better at full throttle, or did you just notice the throttle pedal response was different?

Link to comment
https://www.sau.com.au/forums/topic/449501-v36-370gt-kws/#findComment-7410038
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The Frenchy's kit is the way to go forward. A modern compressor that weighs about 1/2 as much, is at least twice as efficient, and will do a good job on R134a. And of course the kit has everything else you need to connect it up and have it work properly.
    • Hey all , I am in the process of having the AC system in my r32 GTST converted from r12 to r134a and I’m being told my compressor has gone bad and I will need a new one. I was wondering if anybody has any suggestions for what is the best route to go aside from dropping $1500 on a new oem one? I did see that Frenchy’s performance garage offers a kit to mount a Toyota compressor, has anybody actually used this kit on their car? Or is there anywhere I could purchase just a clutch? Any help is appreciated.
    • Well, your RB20 ECU loom won't have wires for the boost solenoid, that boost sensor, and possibly one or two other things. There could be differences in seemingly random things like the charcoal canister purge solenoid, because the 25DET has to handle boost in the vacuum system and the 20DE does not. I don't know - I haven't looked. It is very likely that all the most important things are same-same, being the main sensors like AFM, CAS, etc, and the injectors and ignition. Not that you'll need the AFM for the Haltech anyway. I would suggest that you would seriously want to sit down with the pinouts for both ECUs and just go through them and highlight green what is the same, orange what is different/missing, and make a plan from there. It's not going to be difficult. It will either be the same or need to be fixed.
    • yeaaa that's why I haven't done any wiring to the stock ecu harness because I have the haltech, but then that leads me to the other question of "is the pnp harness really plug and play?" or would I have to still switch some pins/wires over because the pnp is for the rb25det neo harness, and not for the rb20de neo harness. was really hoping to find something to spoon feed me since so many people have done rb20neo + t conversions, but man this is rough.
    • Temu raptor, lol. At least the owner isn't your typical ranger danger lot
×
×
  • Create New...