Jump to content
SAU Community

Rb25De Stalls When Put Into Reverse Or Drive

UCD15R33
 Share

Recommended Posts

UCD15R33 Experienced

UCD15R33

Posted
  • Author
Posted

Sorry guys, Car was been fine up until Wednesday this week. The Car had a miss on Thursday but I found a dead coil easy solved. The auto transmission fluid was replaced Thursday this week. Since then it wouldn't change gear without stalling. I have checked and cleaned the IAC, Replaced all spark plugs, cleaned air filter box and replaced air filter, replace all vacuum hoses but still no go. and replaced the sump gasket.

Ben C34 Grand Master

Ben C34

Posted
Posted

Well it certainly sounds related to the fluid change.

Don't bother with the O2 sensor, that won't cause that.

Does it just die or stop suddenly?

What trans fluid was used and how much?

GTSBoy Grand Master

GTSBoy

Posted
Posted

Won't be the oxy sensor. Will either be a problem with the converter (clutch stuck on perhaps - which could be an electrical issue) or an idle control issue. Can you keep it alive by keeping the throttle open or will it then drive forward? Easy way to diagnose both issues at the same time!

GTSBoy Grand Master

GTSBoy

Posted
Posted (edited)

Sounds like converter is locked. If you're at the limits of your diagnostic abilities at this point, you're probably going to have to tell him to get it to an auto trans specialist. It might be something simple like a wiring fault, but it might be something mechanical that got triggered or otherwise happened when the oil was dropped.

Edited by GTSBoy
FJ RB25 Enthusiast

FJ RB25

Posted
Posted

Sounds like converter is locked. If you're at the limits of your diagnostic abilities at this point, you're probably going to have to tell him to get it to an auto trans specialist. It might be something simple like a wiring fault, but it might be something mechanical that got triggered or otherwise happened when the oil was dropped.

yep thats what I said.
sleptema Proficient

sleptema

Posted
Posted

Pretty sure you mentioned that it does when put in gear like 4-5 times. Righto, thanks mate, wasn't completely sure about that until the 4th time I thought you were just pulling our legs.

What fluid did you use? And how did you change the oil? I have heard of people running the wrong oil (wrong additives/weight) and it would actually weld the transmission and diff together after a while. If it attempts to go into gear it's not the selector. I'd say she's done farked.

FJ RB25 Enthusiast

FJ RB25

Posted
Posted (edited)

Hey UCD

When even trying to diagnose a problem it is often a good place to start at what has been changed as in majority of cases this is a good place to start ( not broke before changing anything but now is after changing something )

You are saying that the trans oil has been changed but you were not present when the oil was changed ( is this correct ?)

And

You had a problem with a coil ( did you test the car after you changed the coil) ?

The problem you are describing sounds like a converter lock up clutch staying locked up ( google how a converter works and you will see some vids on YouTube)

Basically a converter clutch will lock up at a certain rpm, I.e. 2500 rpm stall = lock up clutch will lock up at 2500 rpm

If your lock up is locked up from the get go then you will stall the engine either in reverse or drive.

If the engine is standard then the converter should lock up around 2000 rpm I think.

Not sure how you could test if it is the converter but I would imagine that if the engine was kept above the converter stall it should run. I.e if you took the car to 2000rpm and changed gear each time above 2000rpm or stall then it shouldn't stall in theory.

Now I have had Eff all to do with auto,s but that is what I have self learnt from the net and YouTube, reading books, not having a dig here but look at the net or ring a auto trans shop.

All the best mate, oh and before anyone else mentions

Stick a turbo on that De

Edited by FJ RB25

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Jumbotron
      Parts required for 4:11 diff gears in an R34 GTR Vspec (A-LSD)

      By Jumbotron · Posted

      Hey was wondering if you ended up installing the R33 GTR speed sensor - I found one too and wanted to confirm it's a direct swap into the R34 6 speed?
    • njdgomez23
      How to fix centre console latch.

      By njdgomez23 · Posted

      After 23 years of owning a Skyline, finally had the latch go.  Followed this guide,  works like a dream again. Great Guide 👍
    • marni
      I need more than help to finish my R33

      By marni · Posted

      Hi all,   I’ve got the biggest lot of problems with my R33 GTS-T   It was a freshly rebuilt 25th anniversary RB25DET (plastic cas, neo cams) probably 6 years ago now   The engine was running so well but I fkd up badly and trusted someone I’d known for 10 years that was well known around Plazmaman for his welding and fab work. I added a lovely photo of some of his previous work. Not sure why my car was worked on by whoever did this shit     I’m normally someone who would never open myself up to something like this, I still can’t believe I did it. Trusting him literally fkd it all up for me. Everything has been a struggle, like it’s almost been 6 years that’s how much I’ve just on and off been trying to work it all out.    All I wanted was a car that danced down low, like full boost from around 3~3500rpm to redline, don’t really care what power it puts down (if it ever does) but I just wanted it to be quick to get on it.    He recommended the turbo to get, I picked Hypergear but he told me to get the front 4” with a T4 and 0.68 rear housing.    I was expecting all these beautiful welds, tidy fab work and paid for it to be ready to go to a tuner when I got it back.    I got a car back that was an absolute mess, I actually couldn’t believe it was my car anymore. I don’t think you could even call what he did welds, they’re disgusting.    So I stripped everything he touched off it and with every bolt I loosened it just got worse and worse.    I covered it and literally built and finished another car in the meantime but now it’s getting to the point where I really want my Skyline back.   Its a struggle because I paid him to do all this shit because I didn’t know how to and now I’ve had to try and figure it all out omg    Please excuse the bird shit horrible welds, I’ve got my show pony car and am so beyond dealing with this car I don’t even really care at this point.    If someone told me about what he did to my car I wouldn’t have believed them but it happened to me. It was unbelievable. He went missing, my car went missing, it came back missing parts, the straight af chassis rails bore the scars of being dragged up a trailer backwards, even the sandwich plate was bent. Everything was leaking and open to whatever fell into it, rounded off/ missing bolts, power steering oil and coolant everywhere, no gaskets, parts stolen off it, even managed to damage the sump pan.   Promised me he’d finish the car, knew what it meant to me, I paid him thousands and thousands just for him to trash it. He told me he was fully licensed and insured, come to find out he’d cancelled his ABN, so obviously no insurance. I had laid up insurance on the car and would’ve been covered but I was scared they would’ve written it off or because the business was no longer trading I’d still be liable.    He was supposed to:  New fully custom mild steam pipe exhaust manifold with turbo location moved from factory position to high forward mount. (I don’t know if it is a mild steam pipe, I’ve got a funny feeling the waste gate isn’t in a very good position and I don’t think the outlets off each cylinder are equal) 4” custom stainless steel dump with external gate (he re-plumbed it) Cut and shut OEM intake manifold with throttle reposition (I ended up doing the throttle reposition) Box in pod filter (left out) New 100cel catalytic converter (pretty sure it’s there but unsure if it’s 100cel) Front mount intercooler piping fabricated to suit (all smashed up and rusty holes where he was supposed to make it look standard where fmic piping passes through. I don’t even think my front bar is going to fit 🙄) Custom 5” intake pipe from pod to turbo (didn’t come with it so had to do something to make it work with the Z32 afm)   Engine: Full cylinder head service & machining  Brand new valves Precision upgraded spring kit Engine block honed New bearings  New piston rings  New ARP conrod bolt kit New ARP head studs Cometic head gasket VRS kit   ATR43SS2 ball bearing turbo 0.68 rear housing  Turbosmart 45mm external wastegate (got delivered to the fab bloke, I’ve got no idea what spring is in it, I’m assuming the one that came pre installed) Walbro 260 fuel pump  Nismo 740cc injectors (tested to 880) Spitfire coil packs GCG FMIC RB25DET manual 5 speed 4:11 rear diff   I’ve got an Apexi Power FC in it atm, I was hoping to just get it to operating temp to make sure everything was okay before towing to a tuner but it’s over-fuelling too much. I don’t think that’s going to happen so i think I’m going to get either a Link G4 or Haltech for it. What do you guys recommend? I can’t work out the power FC so just gonna give up on that one     It’s got an exhaust leak coming from somewhere I can’t see 🙄    The fuel pressure was steady but now it like drops from 40 to 20psi randomly (noticed this yesterday)    I’ll attach pics of the shit he put on my car and the engine bay now as it sits    I really just need some help, I need a tuner in Sydney I can trust, I’d like to be with the car while it’s being tuned if possible, I know it looks terrible but unfortunately I’ve just got to put up with it for now and fix the cosmetic stuff later   Do you guys think the manifolds are going to be okay? Or do I throw the exhaust manifold and try again?   I don’t even think these combinations are going to work tbh   I know everything I fitted was rated to be able to take at least 400kW but most rated higher    If you’ve gotten this far I really really appreciate it 🙏 I don’t mind if you trash me or the car, I made a rookie error and f**k I’ve paid for it. As you’ll see 🙄  
    • r32-25t
      Attesa pump mount options / ideas? R32 gtr style.

      By r32-25t · Posted

      From everything I’ve heard you’ll be waiting a long time for  the parts to arrive 
    • GTSBoy
      R34 Manual conversion Speedometer

      By GTSBoy · Posted

      Have you looked at the workshop manual?
×
×
  • Create New...