Jump to content
SAU Community

Recommended Posts

So i've read around but not getting a straight answer, I'm believing it's CAS but coming here for a second opinion

So occasionally the engine will "hiccup". ill be driving down the road (usually I only notice it during freeway driving) and then the engine will like die for a short period of time, (it feels like when you lift your foot off the pedal for a split second)

I think I read somewhere it was CAS but can't since find that page to read up on it.

any help / confirmation / ways to troubleshoot it? Compression is good: 142, 150, 145, 145, 150, 150. New o2 and cleaned AFM.

is running a Power FC

RB20DET 1992 SKyline r32

Thanks for the help guys!

Edited by angusis2fast4u
Link to comment
https://www.sau.com.au/forums/topic/449952-engine-occasionally-hiccups/
Share on other sites

I have splitfires, walbro 255 pump, brand new spark plugs (I forget if this issue was around before I changed them... Could that be it??) So i would hope it's not the coils or pump... Also the issue generally doesn't happen under power like usually just when im cruising along...

How did you check your CAS??

One of my old r32 did that
Checked cas, fuel pump, coilpacks etc
Ended up being dirty AFM

i had an issue like this, but it only happened about like 5000 rpm. then it started to get worse and worse like 4000rpm then above 3000rpm. to the point i could hardly drive my car. ended up being my haltech has a safety cut when it leans out to much it will cut the engine every time its to lean,
ended up being a split hose pipe from my fuel pump to the top of my tank, so the full was getting sucked up the fuel pump then not even leaving the tank squirting out the hose then back down into the tank and then back into the pump again. only letting a little bit of fuel through at a time so was causing it to hickup so to speak, maybe check that, if it gets worse and worse maybe check this. also replace your fuel filter......... cost about $10 and is easy to do! and will rule it out, peace of mind

How does a dirty throttle bofy cause a hiccup?

And a car doesn't need tuning due to new coils. ...

Sounds like the power fc miss.

Just in case you missed GTSBOY ' S post

Edited by Ben C34
  • Like 1

i am aware of that, hence the "other mods" words in there..... clearly trying to sus out and get the most information to diagnose this issue.... you annoy me.

Ok cool. Seems odd you would mention it then.

Sorry that pointing out facts annoys you. I suppose I could just let it slide and let people think they need a retune due to replacing their coils, but hey, I'm not that kind of guy.

I have splitfires, walbro 255 pump, brand new spark plugs (I forget if this issue was around before I changed them... Could that be it??) So i would hope it's not the coils or pump... Also the issue generally doesn't happen under power like usually just when im cruising along...

How did you check your CAS??

Mechanic did back in the days

It was my first car 10+ years ago

Typically to check a cas you play swap tropics with a known working one.

Perhaps there's a way to check it with an oscilloscope, but as the issues tend to be intermittent it would be difficult and unlikely picked up like that.

Typically to check a cas you play swap tropics with a known working one.

Perhaps there's a way to check it with an oscilloscope, but as the issues tend to be intermittent it would be difficult and unlikely picked up like that.

Yeah it like rarely happens like probably not even once a week, It probably only happens like once every 2 weeks

Ill look up the PowerFC miss.

Sparks were done like 600km ago

ill check out that throttle body as well

Thanks for the help ill report back when i've got an update!

The power fc "miss" generally happens coming away from a set of lights, for example. Low rpm, generally low load. Well, mine did anyway.

There is a decent discussion on here somewhere about it.

I had this problem and it was a bastard to track down in the end for me it was the AFM pins getting a dry solder joint.

There is a guide on re-soldering in the DIY section. To diagnose I used CONSULT connected to a laptop datalogging all values. As soon as it happened I pulled over and spotted which value started it, AFM voltage dropping to 0.

Hope this helps

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've watched some vids and the technique seems to be to butt the sheets up to one another and use MIG to spot weld and slowly fill in the spots until its eventually all sealed. No runs as you would normally do, as there's too much heat generated that way. Yeah my stick welds are terrible these days because its been so long since i've done any of it. I expect to be spending many hours practicing
    • I have personally seen a Tomei USA RB26 cam that didn't even fit the head. Kind of nuts to me that it was even possible for that to happen but such is life.  There's two UP Garages in the US. One is a US branch of the Japanese company which sells things they brought over at tremendous markup. The other is University Place Garage/Fairlady Motors which is a shop best known for putting VCAM in RBs and trying to convince people to stop putting in 800hp of turbo on a 2.5L motor.
    • Gasless MIG is not exactly suited to what I would call "delicate" or "attractive" welding. So I would rule it out for sheet metal rust repair type stuff, unless you're only doing it in hidden places. I'm thinking about getting myself a gasless MIG for "hack together" type work. Noting that my welding experience is very very low, and quite a long time ago. So I'm also looking for "simple", but I'm not expecting "excellent". I'm not even sure that proper MIG is the best for sheet metal work. I get the feeling that the degree of control and the minimisation of heat input that you get from TIG is probably what you really want. And then you have to get good at doing it before the welds won't look like a monkey flinging a handful of shit anyway. You're probably SOL for an easy and cheap way to get from where you are to where you want to be. Much like myself.
    • Any recommendations for what would be the easiest welding type to start on, for sheet metal rust repairs and maybe some exhaust piping too? Seems like MIG is the most common. Would gasless MIG be ok to learn on and do some simple jobs? I have a stick welder which has a Lift TIG setting, but i'm more interested in getting whatever's easiest to do, and most suitable, rather than using what i have.
    • Is the UP Garage in the US of Ayyeee even the real UP Garage?
×
×
  • Create New...