Jump to content
SAU Community

Hypergear Highflow, Gtr Bov, Other Bits And Pieces

Yeedogga
 Share

Recommended Posts

Yeedogga Experienced

Yeedogga

Posted
Posted

Hi all,

Just throwing a few things up for sale. Will be updating/adding more over the next few months :)

1. Hypergear Highflow- $650 ono

One of Stao's PU Highflows which is a direct bolt- on turbo for RB25s. Looks totally stock when bolted up.

Utilises the stock compressor housing so that you can use your existing intercooler and intake piping.

Bolts up to standard/aftermarket dump pipes.

Stock water lines can be used with some minor bends/adjustment.

Comes with alloy intake pipe, braided oil feed line, stock compressor outlet elbow, dp gasket and oil drain fitting.

This turbo made 287rwkw on my R33 at 19psi. Tuned by Toshi with S15 480cc injectors, 3" exhaust and return-flow cooler!

It has served me very well, only upgrading to chase more power.

post-55684-14166278159715_thumb.jpg

post-55684-14166278444348_thumb.jpg

post-55684-14166278898909_thumb.jpg

2. GTR bov - $50 ono

Stock GTR bov. Speaks for itself. Larger diameter- flows more air!

3. Stock RB25 R33 turbo- $200 ono

Had less than 100,000km when removed. In good condition.

4. Suede steering wheel - $50 ono

Good condition, a little worn in some areas. Note: Not a genuine OMP

post-55684-14166281586849_thumb.jpg

5. Stock R33 ABS diff- $250 ono

Stock diff, not shimmed or messed around with. Was getting a bit loose when it was removed but could easily be shimmed to toughen it up again!

post-55684-14166282416561_thumb.jpg

Most items located in Dubbo NSW. But can arrange postage on items or can take them to Sydney next time I am down.

PM for any questions!

Kane_R32 Experienced

Kane_R32

Posted
Posted

If anyone buys the high flow and is looking to change the rear to an OP6, I will have one available as I'm going to use a 21U for a little more response. Great turbo otherwise.

Good luck with the sale

  • 2 weeks later...
Yeedogga Experienced

Yeedogga

Posted
  • Author
Posted

Adding this to the thread- 3" bellmouth dump pipe section.

I had to make a new dump pipe so I have this bit for sale.

Would be of benefit to anyone wanting to make their own downpipe (this is the hard bit to make!)

5-Bolt nissan flange. 3" mild steel.

$50 ono

Cheers

post-55684-0-44880300-1417830164_thumb.jpg

post-55684-0-27002300-1417830171_thumb.jpg

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      EDIT: Just a little info what my tranny is "doing" :   For the long time the trans do this "bad" sound:https://www.youtube.com/watch?v=qs_iTXgDt40 It is literally the same sound and same symptoms(when i push the clutch it quites down) So is it really the shaft bearing?   Also:  i found this on forums: The RB20 and SR20 boxes are nearly indentical inside (rb20 has longer mainshaft)and suffer badly from bearing and selector failures when driven hard   The bearing is true and selector failure kinda too...it is "harder" to get into gears specialy when i drive a little bit hard...
    • niZmO_Man
      forum.r31skylineclub.com down or gone?

      By niZmO_Man · Posted

      We will review wtf is going on, but if you made any donations let me know and i will follow it up with the admins
    • MBS206
      Pillar gauges

      By MBS206 · Posted

      See, that button sounds like perfection Duncan! My eyes really don't like light shining at them from a dash when I'm driving. Being part red colourblind, I've found for most cars that I can change colours on, I set everything to red, so my eyes see the elast amount of colour! I miss normal gauges in cars
    • niZmO_Man
      R33 rear seatbelts

      By niZmO_Man · Posted

      bro, knowing the Japanese in  the 90's, i wouldn't be surprised if they shared components across their model lineup.
    • Kapr
      Possible swap on R34 RB20DE NEO?

      By Kapr · Posted

      Maaaan so many "little" things  i rly hope my old RB20 would be "ok" and not too bad. I try to learn what and what not do i need. I look at crossmember at it looks different...even parts numbers are different. Wiring and all that i rly do not know...yeah someone mentioned the speedo thing. On that yoke clip. I rly do not know what can and cant be done "custom" so that is why iam asking to know and not be suprised 🙂  I know what it looks like  
×
×
  • Create New...