Jump to content
SAU Community

Removing Bolts From Top Mounts

AMR33
 Share

Recommended Posts

AMR33 Mentor

AMR33

Posted
Posted

Folks, what is the easiest way to get the bolts out of the top mounts of coilovers. The bolts on mine dont have a hex head or allen key, they are simply round. The thread on the bolts is stuffed so I need to remove them and replace with other bolts. Any ideas how I can do that?

Cheers

Amir

Link to comment
https://www.sau.com.au/forums/topic/450994-removing-bolts-from-top-mounts/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

Generally if there is no hex key in the top of the shaft there is a small flat section below the top where you can hold a spanner. If not I guess you need to try a rattle gun, and if you don't intend to reuse the coilovers lock a set of vice grips onto the shaft nice and tight.

Don't forget spring compressors before you start.....

MrStabby Grand Master

MrStabby

Posted
Posted

Photo please. Duncan is talking about taking the nut of the shock piston (which is how you get it apart) but you said you want to replace them with other bolts, which sounds like you want to replace the piston.... Not making sense to me

AMR33 Mentor

AMR33

Posted
  • Author
Posted

Apologies guys, I should have been more clear. Yes I am talking about the studs which stick out of the shock tower. I removed some from my old suspension but these had an alen key head and were easy to move. I found that there is a small thread in the camber plate which they screwed into. Im assuming the ones I'm trying to get off are similar and have a thread in the camber plate/top mount so I dont really want to hammer them through so as not to damage the thread. Will upload photos soon

Cheers

Amir

GTRPSI Mentor

GTRPSI

Posted
Posted

They are punched/pressed in, in exactly the same way as wheel studs are fitted to hubs.

Put a socket under the stud so the stud can fit through the hole in the socket, sit assembly with the socket on a sturdy bench, whack threaded end of stud with a hammer so its pushed out into the socket.

The whole idea of the socket is to support the camber plate while hitting the stud back out into it.

If you find new studs to knock in and they fit a little too easily, you can go around the camber plate, right next to the stud hole with a center punch, this will shrink the hole a little to make the new stud a tighter fit.

AMR33 Mentor

AMR33

Posted
  • Author
Posted

Cheers Peter. But what if the studs actually screw into the plate? As I mentioned before, another set I tried - the studs were screwed in rather than punched/pressed in. If this is the case with these ones then hammering them out will damage the thread in the camber plate. Any ideas?

GTRPSI Mentor

GTRPSI

Posted
Posted

They won't be screwed in if there's no flats on the head to use to torque them up.

Exactly what he said. If they were screwed in then no need for the mushroom head underneath and there would have been a method to drive them in by a tool.

I highly doublt that they are threaded into a aluminium hat and just hold via some threads in alloy, notice the large flat mushroom head from underneath?

Its so they dont pull through the alloy when tightening the nut.

They are studs just like on wheel hubs.

I have seen a few manufacturers use this method on coilovers and normal struts on OEM assembies, we had one broken on the rear on our GTR, it was snapped off by the previous owner, when looking at it it was a punched in stud, next time i have the rear coilovers out i will be punching it out to replace it.

GTRPSI Mentor

GTRPSI

Posted
Posted

Support the yellow alloy top from under where the mushroom head of the stud is with a socket that is large enough for the musroom head to fit through as you hammer it down.

You need something tubular like a socket to fit around the stud but not touch it, it must sit against the yellow alloy top to support it and provide room for the stud to pass through.

AMR33 Mentor

AMR33

Posted
  • Author
Posted

I managed to get 3 out of 4 studs out. I grinded some of the stud off, hammered it down and finished the rest of with a nail punch. One stud I cut to close to the camber top and I cant hammer it down and the nail punch is simply not doing anything. The stud is sitting flush with the camber top and seems to have welded itself to the camber top from all the hammering etc. Any ideas?

  • Like 1
GTRPSI Mentor

GTRPSI

Posted
Posted (edited)

Heavier hammer with the punch?

This.

Use a solid punch that covers the whole stud face that you cut and use a heavyier hammer so you have some force behind it.

I wouldnt have cut the studs.....

Edit, i just noticed your using a nail punch NOooooo......use a pin punch thats a similar or slightly smaller diameter than your stud.

http://en.wikipedia.org/wiki/Punch_%28tool%29

Edited by GTRPSI
AMR33 Mentor

AMR33

Posted
  • Author
Posted

Thanks for the help boys. Finally managed to get them all off by hammering them, punching them through and swearing at them. All that work and when I was looking at one coilover when it was lying on the ground noticed it was slightly bent. So I have to get it to the suspension place and see what they say. Good times

Amir

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Butters
      UniClutch

      By Butters · Posted

      Uniclutch install vid, RB Track edition.   Highlight reel is very drive able, not noisy but still heavy with the clutch master he has.      
    • GTSBoy
      Left & Right Window Regulators for 2013 Skyline V36 Coupe

      By GTSBoy · Posted

      Replace your battery.
    • GTSBoy
      R34 Gtt Wheel Offset Advice

      By GTSBoy · Posted

      And....if that could be true for all R34 GTTs, then it might be good. But in reality it is not really any better than my standard instruction to "go out and have a look at it yourself, and wave a tape measure around" etc etc, because as soon as you have any adjustable arms, or coilovers with smaller diameter springs, or tyres that have any bulge that goes out further than the rim, etc etc, then the simple version of the information is still potentially misleading. Plus, nothing in this is static. Everything is moving. At the rear the wheels swing inward at the top as they go up, so the clearances on the inside change as the suspension is compressed. At the front it's even worse. And then you have the difference in absolute wheel position in the arch can move around more, or less, depending on how compliant the bushes are. If, like me, you have sphericals on the front caster rods (and on the FUCAs also, but these are probably less dominant when it comes to wheel position), then your wheel will swing forward/backward under loads, as well as up/down, as well as steering angle. You end up having the simple numbers with 17 caveats/footnotes for each.
    • Therry
      Left & Right Window Regulators for 2013 Skyline V36 Coupe

      By Therry · Posted

      Both windows operate normally while the engine is running but start to sag as soon as I switch off.  Does anyone know of reasonably priced replacements or other brands that will fit?
    • Duncan
      R32gtr sputtering and stalling

      By Duncan · Posted

      Actually PowerFC is probably the easiest to get basic data from, it comes with a hand controller and display so you don't need to remember to pack a laptop every time you drive. It also has a PC based viewing/logging option if required. Nissan used consult on these because back in the mid 80s, ODB was just a glint in a standard's body's eyes.  They switched to OBD shape around 2000 (my 2001 Cima had OBD shaped but not OBD compliant port) With the standard ECU there is a cable and software available to give basic data too, I think it is called Nissan Data Scan or s
×
×
  • Create New...