Jump to content
SAU Community

Recommended Posts

ENGINE/EXHAUST

Engine modifications

Block bored 20 thou oversize, decked and o ringed, fitted with forged ACL race pistons and rings

Scat H beam conrods, fitted with ACL race bearings

Crankshaft linished and deflashed oilways

Modified oil pump for greater flow

Heads have received a lot of work with machining, porting and polishing, cc’d, flow tested

1mm oversize Ferrea valves

Competition valve springs

Compression set at 8.5-1.

Inlet manifold has been match ported to the heads and the upper plenum.

JECS 1000cc injectors

Sard fuel pressure regulator and gauge

In tank Sard fuel pump

Custom surge tank and a Bosche 044 pump fitted underneath the car

Custom fuel cooler,

Braided fuel lines

Motorsports connection fuel filter

Battery has been moved to the boot area sealed in a battery box fitted with an isolation switch

Selin twin AFM translator

Twin Apexi power air filters

Series two power transistor unit

Spitfire coilpacks

Engine earthing kit

Modified crankcase ventilation with catch can

2 x GTX 28/63 ball bearing turbos

Recently changed from

UAS custom 600x300x90 front mount intercooler toBDE (Brett Dempsey Engineering) slimline engine mounts to allow for:

Complete 2.5in intake to turbo to intercooler to throttle body piping upgrade

Massive 2.5 inch in and out side mount intercoolers

Blitz dual SBC controller

(Jim Wolf Technology) JWT 400+ wild Cams

BDE (Brett Dempsy Engineering) modified Intake Cam gears

Tomei adjustable exhaust cam gears

A new set of hydraulic lifters fitted with shims has the motor running nice and quiet

Turbosmart, BOV’s

Ross Racing harmonic balancer

Gates blue belts turning the equipment over.

Engine management is by Nistune

56mm Alloy Radiator

72 plate external oil cooler

BEE*R rev limiter

RARE Final Flag polished throttle cable cover (1 actually have 2 of these)

Exhaust

Custom 5 bolt, divorced dump pipes

AMS exhaust manifolds

3” system through hi flow cats, and pair of Varex adjustable Mufflers

DRIVELINE

UAS six button single plate clutch

X-Treme chrome molly lightened flywheel

Chrome molly one piece tailshaft.

Richmond leader diff gears of 4.11 ratio

SUSPENSION

Bilstein PSS9’s coilovers

Powertrix front upper control arms

Powertrix front lower tension rods

Tune Agent rear camber

Tune Agent traction arms

Energy suspension bushings all round

Nissan front strut brace, one of only two in Australia

UAS HICAS lock out

BRAKES

Front,Stop Tech ST-40 calipers big brake kit

332 mm slotted, curved vein rotors

Braided stainless brake lines

Ferodo 2500 pads

Rear, Reliance Edge 297mm slotted rotors

Ferodo pads

Stone shields have been removed and tubular ducting has been fitted for extra cooling

WHEELS and TYRES

Choice of:

19x8.5 and 19x9.5 Lenso gt05 monoblock

18x9 and 18x10 Gram Lights 57F-Pro

Also available is a pair of stock 16” wheels fitted with Mickey Thompson ET street radials for those nights at the drag strip

EXTERIOR

2000 model urethane front bar

2000 rear tail lights

UAS fiberglass vented bonnet

Modified nose panel

UAS rear wing

UAS enclosed rear bar fitted with Perspex diffusers.

Ab-flug Areo mirrors

Custom made Miracle Zed Motors vented air guides for improved cooling to the radiator.

A HID headlights

INTERIOR

Recaro SR3 driver and passenger seats on Z32 recaro rails

Stock gauges have been replaced with el panels giving various shades of blue

Defi triple set, oil, water temp and pressure

Pivot boost gauge

Apexi turbo timer

Twin AEM wideband AFR gauges

Boarder racing gauge hood

Kenwood head unit with four kenwood 5” speakers

Terrano chrome door handles

Leather 300zx logo handbrake boot

Leather 300zx logo shift boot

2000 model gear knob

Leather trimmed doorcards, glovebox, center console etc

535.9RWHP @ 22PSI on BP98 with heaps left. At last tune we didn't even get to start bringing the timing back in when we had spark issues.

Left still to install is a HKS DLI ignition amplifier to fix the spark blowout.

DSC03333Medium_zpsa7c31b3a.jpg

DSC03324Medium_zps19c6f905.jpg

12_zpsd3207d7d.png

DSC03313Medium_zps47cf1423.jpg

20140813_153444_zps9khgd4c7.jpg

  • Like 3
Link to comment
https://www.sau.com.au/forums/topic/451080-mikes-z32/
Share on other sites

Thanks mate, I cant take all the credit for this one, bought it with engine built, just improving on it ;)

After building my old red zed and then getting defected (and subsequently parting it out) I wasnt going to do the whole lot again from scratch

Link to comment
https://www.sau.com.au/forums/topic/451080-mikes-z32/#findComment-7433398
Share on other sites

Scored a HPC coated plenum with 55mm throttle bodies the other night. Been looking for a throttle body upgrade to complete the breather mods for a while now :)

Also I still have to sort of the ducting to the side mounts.

Link to comment
https://www.sau.com.au/forums/topic/451080-mikes-z32/#findComment-7433582
Share on other sites

Becauseracecar

Because v6, 2 banks, 2 intakes, 2 exhaust manis. Already noticing some variations between the 2. Particularly at idle and light cruise. Not small variations either. Need to swap the sensors over and see if the readings swap also. Hopefully they do and its just a sensor on the way out.

Link to comment
https://www.sau.com.au/forums/topic/451080-mikes-z32/#findComment-7434729
Share on other sites

  • 2 weeks later...

So I removed the plenum on Sat, to swap over for another with larger throttle bodies.

Got it all back together Sat night (before the cruise on sunday) and couldn't get the idle down below 1500rpm. I am assuming that it is the butterflies on the new throttle bodies that are leaking :(

Going to have to swap them out again so I can at least enjoy driving the POS over the holidays.

Link to comment
https://www.sau.com.au/forums/topic/451080-mikes-z32/#findComment-7444250
Share on other sites

So after boost leak testing everything, in sections, all I found was a pin hole leak in one of my new hardpipes. Other than that it is tip top. Idle issues seem to have been resolved with a simple TPS reset. Voltage was correct, but wasn't getting a throttle closed signal.

Haven't test driven yet, pointing to should be good tho!

Link to comment
https://www.sau.com.au/forums/topic/451080-mikes-z32/#findComment-7446320
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Back again. I returned to Japan in Jul/Aug to spend time with the car on my birthday and remind myself what all the sacrifice and compromise is for. It happened to line up with the monthly morning meet in Okutama, which I have been wanting to go to for a long time. It's a unique event at a unique spot with really rare, interesting, and quirky cars. It's where all the oldheads and OGs gather. The nighttime scene at DKF certainly has its place and should be experienced if you're into cars, but there's too much bad attention and negativity around it now. IMO the better time is Sunday morning at DKF or Okutama; it's more chill and relaxed. I'm glad I was finally able to go, but not sure it's worth the drive from all the way from Nagoya immediately the day before, unless I was already staying in Tokyo for the days right before the meet, because you have to wake up quite early to make it in time. Funnily enough though I didn't drive the car all that much this trip because it was just too damn hot. While there were zero issues and running temps were nominal and the A/C was strong, RBs already run crazy hot as it is. Sure, it took it all like a champ but something about driving these cars in the ridiculous heat/humidity bothers me and makes me feel like I'm asking too much of it. I'm just me being weird and treating the car like a living thing with feelings; I'm mechanically sympathetic to a fault. Instead I was mainly driving something else around - a KX4(silver) 2001 X-Trail GT, that I acquired in May. There's a few different flavors to choose from with Xs, but visually it's the Nissan version of the Honda CR-V. Mechanically it's a whole different story as this, being the top-trim GT, has an SR20VET mated to a four-speed auto and full-time AWD! It was a very affordable buy in exceptional condition inside and out, with very low mileage...only 48k kms. Most likely it was owned by an older person who kept it garaged and well-maintained, so I'm really happy with how it all worked out. It literally needs zero attention at the moment, albeit except for some minor visual touch-ups. I wanted something quirky, interesting, and practical and for sure it handily delivers on all three of those aspects. I was immediately able to utilize the cargo and passenger capacity to its full extent. It's a lot of fun to drive and is quite punchy through 1st and 2nd. It's very unassuming -in the twisty bits it's a lot more composed than one would think at a glance- and it'll be even better once I get better tires on it(yes, it's an SUV but still a little boat-y for my liking). So...now I have two golden-era Nissans in silver. One sports car and one that does everything else; the perfect two-car solution I think👍 The rest of the trip...I was able to turn my stressed brain off and enjoy it, although I didn't quite get to do as much as I thought. I did some interesting things, met some interesting people, and happened into some interesting situations however, that's all for another post though only if people really want to know. Project-wise, I went back to Mine's again to discuss more plans and am hoping to wrap that up real soon; keep watching this space if that interests you. Additionally, while working in the tormenting sweatbox that is the warehouse, I was able to organize most of the myriad of parts that my friend is storing for me along with the cars, and the 34 has a nice little spot carved out for it: And since it can get so stupid hot in there, that made it all the more easy -after I was standing there looking at the car and said 'f**k it'- to finally remove all the damn gauges that have mostly been an eyesore all this time. Huzzah. The heat basically makes the adhesive backing on the gauge mounts more pliable to work with, so it was far less stressful getting this done. I didn't fully clean it up or chase the wiring though; that will happen once I have the car in closer possession. Another major reason to remove all that stuff is to give people less reasons to get in my car and steal s**t while it's being exported/imported when/if the time comes, which leads us to my next point... ...and that is even though it's time in Japan is technically almost up since it's a November car and the X would be coming in March, I'm still not entirely sure where my life and career is headed; I don't really know what the future looks like and where I'm going to end up. I feel there's a great deal of uncertainty with me and as a result of that, it feels like I'm at a crossroads moreso now than any point in my life thus far and there are some choices I need to make. Yes, I've had some years to consider things and prepare myself, however too much has happened in that time to maintain confidence and everything feels so up in the air; tenuous one might say. Simply put, there's just too much nonsense going on right now from multiple vectors. Admittedly, I'm struggling to stay in the game and keep my eyes on the prize. So much so in fact, that very recently I came the closest I ever have before to calling it quits outright; selling everything and moving on and not looking back. The astute among you will pick up on key subtext within this paragraph. In the meantime I've still managed to slowly acquire some final bits for the car, but it feels nice knowing there's not much left to get and I'm almost across that finish line; I have almost everything I'll ever want for my interpretation and expression on what it is I think an R34 should be. 'til later.
    • Thanks for that, hadn’t used my brain enough to think about that. 
    • Also playing with fire if they start to flow more air down low than what the stock twins can. It's not even up top you need to worry, it can be at 3000rpm and part throttle and it's getting way more flow than it should.
    • Any G40/1000 or G40/1250 results out there?  
    • You still want a proper tune on the stock ECU though. Stock tune + stock ECU with GT-SS/-9s is probably playing with fire if you're running more than stock airflow/power.
×
×
  • Create New...