Jump to content
SAU Community

2015 Datsun/nissan Nationals

Noddy

By Noddy,
in Motorsport Discussion & Builds

 Share

Recommended Posts

Noddy Proficient

Noddy

Posted
Posted (edited)

In April The Z Club of Qld is hosting the nationals at morgan park. It's a Friday to Sunday thing with events from show n shine through to a proper supersprint, timed standing start + 3 or 4 laps. Best session time wins.

Entry forms are not out yet but are close in told. I hear conflicting stories it's could be on the 2100 m E layout or on the full 3 km K layout. They both have a good mix of speed and handling.

More information here

http://www.zcarclubq.org.au/event/nissan-datsun-nationals-2015/

Anyone keen? Duncan?

Edited by Noddy
Link to comment
https://www.sau.com.au/forums/topic/451353-2015-datsunnissan-nationals/
Share on other sites
Duncan Grand Master

Duncan

Posted
Posted

haha how did you know I'd be tempted :)

Hope they run it on the full track, I really enjoyed it....that sweeper on the back straight was great fun

I really enjoyed Morgan Park and will give it a go again, but I won't be ready to go by April.....maybe next time

hrd-hr30 Grand Master

hrd-hr30

Posted
Posted

might bring my Datto out for this if the costs are reasonable. Last DatNats up here was a bit ott.

In April The Z Club of Qld is hosting the nationals at morgan park. It's a Friday to Sunday thing with events from show n shine through to a proper supersprint, timed standing start + 3 or 4 laps. Best session time wins.

unless someone turns up and whinges till they change the format again...

  • 1 month later...
hrd-hr30 Grand Master

hrd-hr30

Posted
Posted (edited)

Z Car Club don't seem to be doing much promotion of the nationals. This is all the info I've seen - doesn't seem to be widely circulated, so spread the word to people who might be interested...

post-15659-0-02902100-1421363207_thumb.jpg post-15659-0-47913100-1421363212_thumb.jpg

Single car sprints as well as multi-car side-by-side supersprints, and regularity for the oldies. Both Track E and K are rippers. K is the full track used in 2010 ASSC with the fast sweepers. Track E is the old full track and has a great esses section where it departs from K. No idea when entries actually open but SEQ people who go to an info night coming up are apparently able to sign on early to the track events. Maybe Z clubs in other states are doing the same thing?

Edited by hrd-hr30
hrd-hr30 Grand Master

hrd-hr30

Posted
Posted

nup, me either. Z Car QLD FB page and website have SFA. I have a couple of mates in the Z Car Club and even they haven't heard anything.

Nissan Datsun Car Club QLD are now trying to get some info out there. They managed to get hold of those fliers and have been posting them on Datsun FB pages. They've organised an info night at Yatala Pies Sunday Feb 1 6pm with someone from the Z Car Club to come and tell everyone what's happening. That's an open invite on a bunch of Datsun FB pages. But its only any good for SEQ people. It's supposed to be a national event, and easter isn't all that far away...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      Rb26 iron block limit

      By r32-25t · Posted

      You don’t need to use full throttle all the time to break these blocks, 500kw at the wheels in more then enough to break them even with an occasional squirt. Hell I’ve seen them break under 400kw
    • Dose Pipe Sutututu
      Question about BoV on RB25DET NEO

      By Dose Pipe Sutututu · Posted

      A work around is to install the R35 card style AFM/MAF on the cold side of the intercooler piping and the BOV on the hot side piping. Works well, also you can combat the revs dropping by adding a bit more ignition timing on the idle ignition timing table to slow the rate of RPM drop.
    • Predator1
      Rb26 iron block limit

      By Predator1 · Posted

      Understood. If you dont have a ridiculous limit,  Tune, T's and P's are in check, and arent bashing it all the time and doing the due deligence for maintenance(inc oil analysis) then its pretty safe. 100% agree, let your right food control it to some extent.
    • Roy
      Rb25/30 Rb30det Vvt Internal Oil Control

      By Roy · Posted

      So these external kits with the machined block for remote solenoid mount will only work on a NEO head and RB30 or RB26 bottom end   For an R33 head on a 26 bottom end the remote vct kit is to resolve RB26 manifold adaptor plates etc  IF you try to use the remote VCT on an RB30 or RB26 bottom end with an R33 head then  you can starve the cam journal??? I have one of these kits from bits I had years ago before plans changed  I don't understand how that tracks with this video   https://youtu.be/RuPiI22Mplk?feature=shared   This looks like I can run the v termite vct kit to feed the VCT on an R33 head on an RB26 bottom end?!?!?   Lol.... don't v have these problems on RB20s
    • Kapr
      Question about BoV on RB25DET NEO

      By Kapr · Posted

      Yeah i know that MAF is no no for this type of BoV. The engine has no BoV and "hose/pipes" ..it was all deleted (or probably it was not even on the engine when it was bought  ) It does that "sutututu" noise which i kinda do not want(atmospheric is better IMO...but standalone ECU)  What are the cons of running without blow off on stock RB25DET NEO. It running 5-7 PSI max (it has boost controller)   EDIT: and can Nistune be "tuned" to know there is no BoV to i dont know "know" and be better for a car? I read so many info about no BoV. One guy saying it is bad and hurting the turbo/engine/car and other that it does not...  
×
×
  • Create New...