Jump to content
SAU Community

Rb30 25 Neo Build


lcxu105
 Share

Recommended Posts

Was speaking with a bloke the other day and he said that the top deck of the block needs a different finish for the cometic head gasket. Never used them before so don't know if this bloke was telling the truth or Tring to blow smoke up my arse.

Realistically any MLS gasket needs a nice smooth surface to seal properly.

But if the block is already built, I would just spray some Hylomar on the gasket. Might work fine Dave.

Link to comment
Share on other sites

  • 4 months later...

Well bottom end is together and the head is at the machine shop for some valve springs and port work. 

Should have it back next week.  

Hopefully will be in the car by the end of the month.  

Fingers crossed

Link to comment
Share on other sites

  • 2 weeks later...
  • 3 weeks later...
  • 7 months later...

Ok. Im just looking at changing the plugs to run flex fuel and 26psi max boost. I know everyone has different ideas and needs. Was thinking about sticking with the factory iridium plugs gapped at .6 but instead of the 6heat range going to a 7 or maybe an 8

Any tuners want to give me a heads up or point me in a direction. 

Link to comment
Share on other sites

I was thinking about those as well.  

I was going off the NGK id sheet for part numbers and did some net surfing to see what had the best bang for buck. Thats how i came up with the  BCPR7EVX.

The evx plug is fine wire and for boosted applications.  The fine wire alows the ignition system to create a better spark with less power. 

See attached pic for part number info. Please note that the ix plug is not listed. 

Screenshot_20170404-194732.png

Link to comment
Share on other sites

For my own car which had a slight miss at high revs at about 320 AWKW or 425hp on the dyno with new OEM coils and   BCPR7ES my (Japanese ex Nissan) tuner suggested PFR7G which fixed the miss.

  • Like 1
Link to comment
Share on other sites

  • 2 weeks later...

What water pump did you use. I've read around that the RB25 has an extra bolt which you may have to tap the block for. If it's not done right it could leak from the top of your water pump.

 

Have you thought about how you will run Internal/external feed for the VCT and front cam journal? I'm pretty sure it's a little different on the Neo Head.

 

 

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...