Jump to content
SAU Community

Rb25Det Neo Into R32 Gtst Problem?

Ryan!

By Ryan!,
in Engines & Forced Induction

 Share

Recommended Posts

Ryan! Rookie

Ryan!

Posted
Posted

Hey Everyone

I have just put a standard RB25DET NEO into a R32 Gtst.

Engine was out of an Auto r34 GTT rb25det neo)

Ecu and loom is from a manual Stagea (rb25det neo)


It ran perfect after i connected everything, took it for a spin and went great through all of the gears ! running 10psi

now on my way back from testing i went to give it to it a bit and all it did was bog/misfire under load, so i thought maybe coilpacks/ spark plugs/ afm etc,

Okay so i changed all that, bought new platinum spark plugs new conditioned afm, and another set of coilpacks, went for another drive, and again went good, THEN on the way back same thing its like as if the ecu reads something wrong and it goes into limp/safety mode??? also like to mention runs really rich too.

OKAY now i have worked out when i disconnect the afm and put it back in its like as if it resets everything and when i go for a drive i get about 10 seconds of running good then it goes back to bogging/ misfiring under load.

Is there something im missing that needs to be connected to the ecu ?

what is causing this to happen?

Also I dont have a diagnosis plug haha

and wanted to also ask if i buy a power FC with hand held and connect that to a computer will that tell me what is wrong, and a friend of mine told me a power fc ecu does not have limp/safety mode so will run normal with one, is this true?

Thanks kindly !!

Link to comment
https://www.sau.com.au/forums/topic/451452-rb25det-neo-into-r32-gtst-problem/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Well, this is probably where a wiring diagram and a multimeter come into play.
    • Jarsky
      gauge needle removal

      By Jarsky · Posted

      I can say to anyone thats doing this; having done a number of R clusters; just be careful if its an unknown cluster.  It takes a bit of force to pull up; but if it feels excessive then its probably stuck. I've had this and pulled the entire hair spring out; and I can tell you; its not easy getting the correct spring replacement with the correct inner diameter and winding. In my case someone had used some sort of adhesive to stick it to the spindle and it pulled the whole spindle out; which the force seperated the hairspring from the spindal and caused it to deform.  You may have to clean it (IPA); or in my case if i'd known i should have used some sort of solvent on it.  Also check out Cruizin Central on eBay. He does all sorts of dials; and you can email him with any custom designs you want. So if you want like certain logos etc...he'll send you a mock of what it will look like then you accept the order and he'll take care of the rest. Fantastic dials and he can do basically any design you want. 
    • Jarsky
      R33 GTST Axles

      By Jarsky · Posted

      Have you confirmed its the actual axles? Also the wheel bearings that mount on the hubs to hold the axles wear out. I replaced mine as they got play in them. It sorted my play issue. 
    • Jarsky
      R34 Speedo not working after manual swap

      By Jarsky · Posted

      Ive converted a few clusters for the R33 with 320km/h dials. On the back there are some pads which can be bridged or unbridged (using solder or wick braid) to calibrate it. There is one bridge which is for MPH <> KPH; and there are combinations of bridges to offset it. There is probably a diagram  For example; this is my conversion for a 180km/h dial to a 320km/h dial (I put custom GT-R dials on it with the GTS25t layout) If you have J2 soldered (assuming the S clusters have a similar config to the R clusters); you may need to remove that solder
    • Rezz
      DeAgostini 1/8 scale BNR32 Nissan Skyline GT-R Nismo

      By Rezz · Posted

      Back on topic 😉, these are some of the notable pages from the booklets that are supplied with each weekly parts update. I never knew the BNR32 test mule car had an S13 Silvia front end... *Edit: On closer inspection the test car still had the R32 body, but only the front end had Silvia panels etc.
×
×
  • Create New...