Jump to content
SAU Community

Recommended Posts

Cleaned the shed of diffs from my old track car, they have not had a lot of

use as they were spare diffs for various tracks, none have been used in the last 5 year

since I just run what I brung.

No drifting use, some road use as well, not abused on track. I would be classed as "smooth". I started track 15 years ago in a 400hp rx3 with a 2 way and tiny axles, I had to be gentile on the drivetrain as axles and LSD's were rare or super expensive and continued to drive that way.

All come with S13 rear covers so reuse your own if 2 bolt type. All are 5 bolt flange.

4.08 1/2 way interchangeable currently set to 1 way $850, I think its a kaaz (should have under 4k klm)

4.363 2 way $780 possibly tomei, maybe kaaz too (should have under 4k klm)

I only used factory oil + Castrol LSX lsd oil in all of my clutch LSD's

3.9 with viscous center $450

4.08 housing and gears only drop in your center, change rear cover if needed and go! $450

4.363 viscous $450

4.363 ratio only $260 shipped

4.363 crown wheel only (couldn't find the matching pinion $100 shipped)

Sorry I cant be more specific on the make of the aftermarket diff's, the tag either broke off or the writing faded so can only go off what I see

Pick up from Bankstown or Epping, currently can only ship just the 4.36 ratio as the others are too heavy to send via post.

Edited by sucram
  • 7 months later...
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As GTS mentioned, it takes a bit of faffing, some fiddling and a little modifying.  With the strainers, you can buy different styles. Some sit flat on the pump, some angle down.  Here are some photos of mine, ignore the ugly welds lol. 
    • The smart thing is to actually locate the pump at the right point down the hanger, so that the strainer can stay sticking out at a right angle, but near the bottom. This is the perpetual hassle with retrofitting any different pump to the factory hanger. Some just go where you need it to, some need fiddling and faffing, and modifying of stuff.
    • Some updates. After a lot of praying and some inspecting of crank threads, we've found that they were both kinda munted but nothing seemed terminal. The other option was drilling and helicoiling the crank. That is obviously the last option so we decided to at least try to get a OEM GM bolt in to GM Specs. So after honing/linishing the balancer from it's .002" interference fit to a .0018" to .0015" to .0013" it eventually slotted on to the crank. ATI state the interference is nominally 0.0007-0.0009... so it's still snugger than ATI reckon and explains the issues we had to fit the thing to begin with. New GM bolt went in at 37 ft/lb then torqued 140 degrees after which was EXTREMELY   but it tightened up to 140 degrees and it was a lot of force. So all things considered, the balancer is secured to the exact specs that GM want with the OEM Stretch bolt, (that ATI say you can use..) and the balancer itself is seated and snug AF. So WOO. Engine is now back in the car with lots of swearing. Bellhousing bolts done up, driver side manifold is on, AC Compressor and hard lines are back on the car. Next step will be to connect various engine bits/wiring/intake/radiator etc. Then oil and coolant and ... test start it? And of course, looking into this issue... which actually doesn't look so bad - It looks like it can be twisted back into shape with a set of multigrips. Anyone wanna buy my bonnet? Boy it looks good over there and sunk cost sucks.
    • Also this may be a stupid question, but how would you recommend getting the strainer on a downwards angle ? as they tend to obviously clip to the bottom of the pump which usually sits level 🥴
×
×
  • Create New...