Jump to content
SAU Community

R32 Gtst - Track Car


bcozican

Recommended Posts

22 hours ago, bcozican said:

The car sits on a combination of hard packers and progressive poly bump stops after a certain amount of suspension travel that only allows the car to go so low - which what keeps it off the ground 

The suspension travel - droop etc is all limited to a smaller specific range by spring perch/ bump stops and various other things

Does this ever bite you? Like in slower turns where the suspension is compressed but not quite on the stops, where a track bump or kerb will kick the travel into the stops?

Link to comment
Share on other sites

Surprisingly not - or not that I have experienced to the extent its been detrimental - overall the car is the most  compliant its ever been to be honest

In saying that I dont go near high ripples and only take on very low one, bumps on slower corners circa < 100 kmph seems to go fine - relative to a more circuit only orientated suspension setup with no aero I cant say because its been a while now so my perspection might be skewed

We have a track down south at Collie that that is more technical and slower speed corners it handles it relatively well but has a very bumpy back straight I struggle there at speed it skips sideways half a lane at times but not unbarable but I dont think my car is optimal for that particular track 

 

Also I might add tyres and tyre pressures play a big part in all this - part of doing all this was moving from a 295/30 to a 295/35 profile tyre its a big difference in height of sidewall - the difference in compliance and extra 'squish' of the tyre aids in both mechanical grip and compliance/ handling with the stiffer/ limited travel suspension and management of total actual car travel under compression over and above what the suspension does... but then you also have to take that into account to keep it off the ground also

 

Edited by bcozican
  • Like 2
Link to comment
Share on other sites

6 hours ago, soviet_merlin said:

Looking forward to seeing you drive this in anger over here in Sydney!

I bought tickets for the WTAC session on the Saturday. We'll be rooting for you. Didn't even know this was coming up before you mentioned it.

https://worldtimeattack.com/

Thanks mate! yes its only 7 odd weeks away and my cars not even ready yet 🙄 😅 typical.. 

See you there!

 

  • Like 1
Link to comment
Share on other sites

1 hour ago, Komdotkom said:

Good to see you are going mate, it's a big commitment to get there from WA.

The workshop I use has a car in Pro Am this year and is hoping to get into the 28s.

 It massive to get over there, compete at a decent level and back

cant be a big fish in a little pond in w.a forever im ok with it being the other way its a challenge

nice 28's is extremely fast. we think we got a decent idea what my car can do... the problem being the driver and the lack of SMSP track time. But thats part of the game!

  • Like 1
Link to comment
Share on other sites

I don't think a 28 is realistic but the owner thinks he's Verstappen, but they should do a high 29 if the weather is good.

A good mate of mine has done quite a few WTAC's and reckons the hardest bit is banking a decent lap without getting blocked while the track is fast. He came 3rd one year but that was before people lost their minds and built cars like RP968 and the Tilton Evo.

Good luck mate, are you getting Brad to help you with setup/engineering? I assume he'll be there anyway.

Link to comment
Share on other sites

I know alot of people like that 😄 Im the other way - car is good Im junk so I have to work harder

Which Pro am car is it ?

The reality of the combo reaching its potential first time out is extremely unlikely but hopefully have a decent experience and hit out and you never know

Yeop he will be over here in just over two weeks for a few days to get us in the working window very quickly then will be heading things up with the rest of my guys as obviously he has a few other cars too

Link to comment
Share on other sites

26 minutes ago, bcozican said:

negative

Get with the program mate!  I knew there was something you hadn't upgraded on this thing.

I'm in the process of doing it with mine at the moment, I'll shoot you some details once it's sorted.

  • Haha 1
Link to comment
Share on other sites

8 hours ago, Komdotkom said:

Do you run IR tyre temp on this thing?

Is that an IR setup to get a reading across the tyre, not just a single temperature per wheel?

Link to comment
Share on other sites

On 14/07/2023 at 9:54 PM, MBS206 said:

Is that an IR setup to get a reading across the tyre, not just a single temperature per wheel?

Correct, 300mm wide temperature gradient. Might be a bit narrow on this thing though with the massive boots it wears!

Link to comment
Share on other sites

8 hours ago, Komdotkom said:

Correct, 300mm wide temperature gradient. Might be a bit narrow on this thing though with the massive boots it wears!

Got link to the specific device you're using?

I know someone who may be interested in one for his production race car.

Link to comment
Share on other sites

In the absence of any good quality and low cost units I've decided to make them myself with the assistance of a friend who's an electronics engineer. The components are quite cheap and he's a boffin so I'm just waiting for him to work out the Motec can protocols and I'll have them sorted. It won't work for other systems, will need to be Motec unless your device can configure can messages.

  • Like 2
Link to comment
Share on other sites

12 hours ago, Komdotkom said:

In the absence of any good quality and low cost units I've decided to make them myself with the assistance of a friend who's an electronics engineer. The components are quite cheap and he's a boffin so I'm just waiting for him to work out the Motec can protocols and I'll have them sorted. It won't work for other systems, will need to be Motec unless your device can configure can messages.

Funnily enough the person who would want it runs Motec.
And I myself spend a shit tonne of my working time doing reverse engineering of CANBUS, and Electronics Engineering ha ha.

Just no time left to take on more projects (I have enough already right now :( )

Keep me in the loop on what you're doing :)

  • Like 1
Link to comment
Share on other sites

  • 3 weeks later...

Usual photo dump from me:

Full hotside and rewire done - I dont get excited about much but the wiring is top notch

Enginedyno.thumb.jpeg.d67acaac97a8c3b41ab1abdc0ef38a39.jpeg

 

The office is functional and comfy - getting to be alot to remember and think about though sometimes 😆

 

Office.thumb.jpg.402ef7bdc07b7a0bda61bc1ae3f68ee3.jpg

 

Fuel system wasnt going to do what we wanted to updated with new surge intank with some walbros and super mega flow fuel filter + wiring and sensors

 

NewFuel.thumb.jpg.1cfdc0b1fdf25cd93a0cd4120ef51a63.jpg

 

Finally got it home after few months gave it a wash even in the rain ha

 

Wash.thumb.jpeg.544021df31a77aeb476d936fd60a4314.jpeg

 

Fitted up the new Syd Comp aero few other bits got some wrap fixed up and nearly ready

Newside.thumb.jpg.46bd6cf23ecb1f3f7d21418d37a8c65d.jpg

 

NewFront.thumb.jpg.8bce58d07b0cee92ccf7e61358af8564.jpg

 

Dyno time was on with the team all went relatively well made good powas - was injector restricted even pushing them to max but did the numbers needed

 

Dyno.thumb.jpg.118a4b1b767438fbe5f9c51ec4b1259e.jpg

 

was back to my house for full suspension check, look over, change and other things.

Finally got a test day in 

TestDay.thumb.jpeg.78d72d183f5127e1b3300eb02cc70cae.jpeg

 

Didnt take us long to get it working very well - pretty good result in such a short period of time, surprised me, but if you look at the million hours of work that went into the lead up it should be expected but not always the case.

 

Car is just good. Full stop

 

We came a way with a list of things to change, fix and ammend but nothing major its just work to be done in the next 3 weeks then we are off

 

 

  • Like 8
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As far as I know, Infiniti stopped importing vehicles before 2020, even though they were still selling their stock for at least a year or 2 after that, they were older build years, therefore, you can import a 2020 400R, because you couldn't buy an AuDM 2020 built Q50 RS. As for insurance, you might need to go through one of the enthusiast insurance companies, they tend to insure a lot more grey import models than the mainstream insurers as Duncan mentioned.
    • loved seeing the zenvo on the a1 just after the hatfield tunnel i was the guy in the white van trying to egg you on it sounded awesome and those exhausts glowing red inside insane cheers for the thumbs up tim and tom.
    • So.... when I'm finally getting around to having my power steering leak sorted, now it looks like I've got the same issue most A/T Skylines are having. My A/T light will randomly come on and I'm stuck in 3rd gear until I turn the car off and on again. Only 3 weeks ago I did a complete transmission service: Oil flush + new gasket + new filter. This came out of nowhere!! It wasn't like the car was driven hard. I drove about 3 mins down the road to get fuel and boom!!!  Anyway, I have a few questions and hope you fine people can help me out here. All questions are in red. 1. The solenoids: I was looking at the parts catalogue in Amayama and I could only find the Solenoids as an assembly. https://www.amayama.com/en/part/nissan/319404ax05 I read in another thread that Solenoid A = 31940-4AX02 & Solenoid B = 31940-4AX05 but the Amayama product has only the code of B. Is this the right part? Can anyone who has done the Solenoid changes or seen them confirm if this is the complete set of A & B?   2. Gasket and Filter: I'm not going to try change the solenoids myself because it seems difficult to do in a home garage with just 2 jack stands. I plan to take it to a shop and get it changed. I was also going to buy the transmission sump gasket at the same time so I don't reuse the same gasket. Should I just use the existing gasket as it has only been on the car since OCT 19th? (~3 weeks) Should I be buying a brand-new gasket and a filter? Does this job involve taking the filter out?   Thanks in advance to everyone. It's hard to find a video of someone doing a solenoid change on a R34 so any help you can give answering my remaining questions would make me less stressed.
    • Yea - From what I have seen from the video, the car idles like any R34 lol 50PSI of fuel pressure is hardly super abnormal, the regulator is working because the pressure remains static when the throttle gets revved, i.e pressure remains the same when manifold vaccuum changes. Bigger pumps on stock rails always bumped the pressure in the rail without using an aftermarket regulator to change that. Do you know what your IAC is actually doing? Has there been any data showing the stepper motor % etc? There's no way your idle is actually moving around the way the cluster(s) are indicating. You would hear the difference with the engine RPM flying to 3k and 1k in mere seconds. I'd be checking the wiring to the tacho. What the tacho is telling you and what the engine/ecu is telling you are different things. I assume your ECU doesn't display the spike. So whatever is telling the tacho to be at X rpm is doing something weird. When the going gets insane, you're on the wrong path. You've ruled out plenty of things that are working correctly/aren't the issue. Your idle isn't doing what the tacho is indicating. You have two seperate issues, I don't think they are linked, and the idle seems reasonably okay unless it's stalling which.. well, it hasn't. Troubleshoot the stall if it occurs by figuring out what your IAC is doing vs what it is being told to do.
    • So awesome! I love the RB with the exhaust on display.
×
×
  • Create New...