Jump to content
SAU Community

Recommended Posts

Ok so I'll start at the beginning my R34 Gtt series 2 had the exhaust wheel snap off the turbo, as I am on a budget I bought second hand standard turbo, running standard boost it drove fine for about a week, then all of a sudden I noticed a noise like a squeal and my boost dropped off, so immediately stopped, it hasn't over heated nor is the oil creamy so was hoping someone might have some idea don't want to pull off the head if it's just a cracked turbo internally is there some way of checking I noticed aswell that I can idle the car no squeal or anything seeming wrong but if I rev I'm getting boost but when it hits max it drops off and I get exhaust fumes out my radiator, any help or tests that I can do would be greatly appreciated I'm on a budget but if it comes down to it I'll pull it off the road until I can scrape enough coin to do turbo and head/ gasket if required but that'll take a long time to save

Link to comment
https://www.sau.com.au/forums/topic/452443-need-help-r34-engine-issue/
Share on other sites

Sorry should of been more specific the squeal was the split in the header tank and I did use brand new gaskets etc when fitting the turbo, I'm more looking for a test to work out wether the exhaust gasses are entering the cooling system from the head or internally in the turbo

Ask at Supercheap or Repco. Combustion Leak Tester.

You should be able to buy a kit that will tell you if there is Exhaust gasses in your coolant by the change of colour. (blue to yellow)

Instructions will be on the kit and should take less than 20 minutes.

You can also do a quick test by removing your radiator cap to see if your getting bubbles.

If so:

It will be the head/head gasket.

Edit: Not to say your Turbo isn't screwed also

Edited by Sinista32

I am getting bubbles in the radiator that's how I know that the exhaust is leaking I'm just confused as I thought the head/ head gasket would've allowed coolant into the oil or vice versa ill do a compression test and see what I get, do you know what it should be reading if the engine is within spec, and the only reason I'm suspecting turbo at all is because it's the only thing that's changed and is oil and water cooled so I thought there's a possibility that it could cause exhaust in coolant should a seal fail or housing crack, and because it idles fine but when I accelerate the boost guage hits 7 then drops straight to zero so stops boosting

I'm always surprised how people think a head gasket failing will always mix coolant and oil.

Looking at a gasket it's the least likely scenario. There's heaps of coolant galleries and not many for oil. So typically a blown gasket leaks coolant only.

For now the leak is small. Keep driving and you will eventualy see oil in the water. Second hand turbs never a good idea. As for turbo causing gasses in the radiator - no.

So there is no chance that the turbo cracked internally and is feeding exhaust gasses through the cooling section of the turbo out into the cooling system, and ill do compression test ASAP and post results, in order to keep driving the car ill have to get new radiator because too tank on radiator split open so it would've had to over pressurise the cooling system

I'm always surprised how people think a head gasket failing will always mix coolant and oil.

Looking at a gasket it's the least likely scenario. There's heaps of coolant galleries and not many for oil. So typically a blown gasket leaks coolant only.

I do understand what your saying but wouldn't you still likely get an overheating issue or smoke out the exhaust?

I do understand what your saying but wouldn't you still likely get an overheating issue or smoke out the exhaust?

No. It will overheat when it loses enough coolant. It only creates steam when a fair bit is going through. Small leaks don't show up easily.

That's why there are test kits available for checking for the precede of exhaust in the coolant.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good morning all, Bit of a random question but figured I’d finally throw it out after wondering for a long while. Before I start, I'm hoping to do this purely out of personal preference. I think it would look better at night, and don't mind at all spending a few hours and dollars to get it done. I've copied this from a non-Skyline specific forum, so I apologize for the explanation of our headlight switch setup that we all know. Here we go: Zero lights (switch off) Parking lights (switch position 1) being a rectangular marker on the outside of the housing, my low beam being the projector in the centre (position 2), and a high beam triggered by my turn signal stalk. Most North American cars I’ve owned of this era have power to the amber corner (turning indicator) light as part of the first switch (parking lights). I’d love to have these amber corners receive power when the headlights and parking lights are on (headlight switch), yet still blink when using the turn signal which is of course a separate switch. Hopefully I’ve explained my question correctly. Is anyone aware of a way in which I might be able to achieve this? Thanks in advance
    • My heads are cathedral port! It's likely possible, but I don't want to add any extra moving parts (I know they don't move) between the heads, manifolds, etc. It will also affect how injectors/fuel rails etc sit and I don't really know if it would change how the FAST manifold goes/sits/fits. I have the LS6 steam pipes already as I have a very late LS1 block so it should be fine. I couldn't find anyone who had ever actually used one for this purpose, it seems 100% of people grind the water pump. The thermal spacers are 12mm and are half way to the cost of the newer water pump anyhow... so if it comes to that I suppose I'd rather buy a new pump. The bearing in the pump I do have is a little.. clunky, but it hasn't done that much time and I never noticed it when the car was together in the past few years, so..
    • The bushing has failed, not all that uncommon for a car of this age.  Any mechanic should be able to push in a new bushing for you, or you can probably buy the entire lower control arm, complete with bushes.
    • Could you not use "thermal" spacers to give the clearance, like the ones I used between the blower and head? That raised the manifold height by around 10-15mm Albeit the ones I used were for cathedral ports, but I assume they have similar for rectangular ports????
    • Thanks Paul I reached out to Autotainment but they no longer work on JDM cars as the guy who used to do the work moved on and is no longer doing that kind of work. I am talking with Level Up Audio though.
×
×
  • Create New...