Jump to content
SAU Community

Recommended Posts

FIIIIIIIInally got the car tinted. why i didn't do that before summer i do not know.

anyway when they guys were tinting it they found that the top of the window was no longer sealing.

i knew the rubber was coming up, but the actual sealant between the window and glass has failed. water would be coming through it this winter OR, it would pop out... that would not be coos as its a genuine wiperless window and irreplaceable.

top ruber just falling away, would not reseat at all.
20160212_072802_zpsdxccerdc.jpg20160212_072738_zpswpmomj9s.jpg

bottom edgings are shit aswell.
20160212_072745_zpsv18zouum.jpg

i plan to paint the car or at least roof at some point so i will be ordering a full set of genuine rubbers, seals and surrounds at that point, but for now i just need to make it functional.

window out, quick rust check, there are a couple of little spots but nothing that cant wait untill the proper paint.

20160212_114118_zpse6tiuor0.jpg
20160212_114048_zpstbypncvf.jpg

this is the corner that failes, rust spot

20160212_114128_zpsotiyeqsd.jpg

We cleaned it all up and put some treatment on it and resealed it all up properly.

new seal

20160212_195716_zpsfn1sleao.jpg

un sure what i want to do at the base, i have ran the seal under the old metal frames, i will be re-using these when i get genuine seals, but for now i have just left the tabs overlapping the new rubber, the only way it can be blended and sealed without genuine bits. it will do for now.

20160212_195616_zpsg2z6pdge.jpg

  • 2 weeks later...

the little misfire reared it ugly head again, so i decided to rip open the afms,

the solder looked fine tbo, didn't seem cracked or loose.

f380e707-22c0-4961-bb2e-ddcca024ffda_zpsfc2cc972-1fd9-4ffd-a6c3-26301cb7ba5c_zps

but i re soldered them anyway, i honestly added the smallest amount of solder, and resealed them back up.

this is a shit job, cutting away sealant and trying to reseal them without it looking shit house.

but yeah, misfire completely gone, so happy when simple things work.

Edited by GH05T
  • Like 1
  • 1 month later...

haha, yeah their allot easier to tint without the wiper too :)

Flex fuel... maby, not for now.

remembering im still running a stock motor, stock turbos, stock injectors....for now.

pulled the spark plugs out for new ones, they are about 2+years old and looked healthy which is nice.

Josh at forge was nice enough to get me the haltech so we hooked it up. its got the tune from his stock gtr so it was drivable, feels sharper already, it will be booked in for a tune with Garage7 to get it up and boogieing. then I will look at new turbos-dumps-fuel pump-injectors - maby a new cam - yada yada... at that point I will look into flex.

it is no longer a daily so I can deal with the availability and added maintenance, so I should...

must resist using antilag with stock turbos :P

im very interested in the tune difference with the same boost from stock computer to the haltech. im not expecting more highend realistically but keen on the midrange. I will report back once its done to compare.

Edited by GH05T

Thanks man,

I'm eagerly awaiting a time i can get it into Garage7 for a proper tune, very keen to drive it finally knowing it has a proper tune. Up until now it has had its MINES ecu, while it had the 8000rmp rev limit on the box you just never know what its actually tuned for. like I said im not expecting more power specifically as I will essentially be running the same boost (depending of the AFRs it yields) of about 12-13 psi.

It made 258 rwkw last time which was quite respectable for stock everything except exhaust and pods.

im more hoping for the midrange and the sharpness and general driveability without being a rich pig like it was, and of course having the safety features the HALTECHs have so I can give it more without worrying so much.

just waiting for a booking now.....

Edited by GH05T
  • 2 weeks later...

damn tune had to be moved to the 10th .... damn Anzac day deleted my day off which I didn't realise.... le sigh...

maby I should take this time and put a fuel pump injectors and a cam in it...................... you know...... for good measure...

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



×
×
  • Create New...