Jump to content
SAU Community

Recommended Posts

Hi All,

Can someone help me out with this,

Need some tips on the settings I should run on my r34 gtt for a wheel alignment, looking at setting the car up for drift.

As for suspension gear it is fairly stock aside from bc coilovers, adjustable castor rods, adjustable front and rear sway bars and tie rod ends. All the camber arms and bushes etc are stock aside from this.

Can anyone shed some advice on the set ups they have tried and tested?

Any help appreciated.

Link to comment
https://www.sau.com.au/forums/topic/452956-wheel-alignment-settings-for-drift/
Share on other sites

My 2c.

Run some toe out on the front to help the car turn in. Too much toe out on the front will make the car twitchy in a straight line however.

Start off with zero toe on the rear and add some toe in once you get comfortable.

Start with 7-8 degrees of positive castor. Circuit drivers will tell you to wind in as much as possible, but too much positive castor induces positive camber on the inside wheel at opposite lock.

Keep the ride height at a suitable level so the standard geometry can do its thing. Too low and you start messing the roll center, bump steer etc.

Start with the rear swaybar on hard and the front in soft and go from there.

I like to run the dampening on the softer side on the front and stiffer on the rear. Others will tell you otherwise. Start midway and see how the car feels.

So something like this.

Front toe: -6mm total (-3mm each side).

Castor: 7-8 degrees positive.

Rear toe: Zero.

Good luck.

Thank you for the advice really appreciate that, will try those settings.

I am raising the ride height as it is a bit too low especially in the front, want it to be able to turn without scrubbing. Interesting to run the front dampening softer than the rear have always heard people say front needs to be harder then rear, will try it though can always adjust on the day.

Yeah the dampening settings are more a personal preference, I like how the car feels and responds that way. You may find that it doesn't work for you, but every setup is different. As you said, adjusting the dampening is probably one of the easiest ways to change the balance and feel of the car, it's all about finding what works for you and your cars setup.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Gday, Due to not finding much up to date info on this topic I thought I'd make a thread to get peoples latest opinions/recommendations. Background info -  I've got a S1.5 R33 GTST as a fun project car, mainly for street use and occasional drag strip, apart from all the cosmetic things I'll be doing a full rebuild of the engine with forged internals. Since it'll be getting new cams (kelford) and springs to match I thought I might as well get new lifters and valves while I'm at it, the dash says 160k KMs but the engine seems pretty tired, compression measures about 130psi across all cylinders so I'd like to freshen everything up. This is where I'm tempted to just fork out the extra and go solid lifters while it's all apart, aiming for 400-450kw atw with a flex tune. Assuming all supporting mods (oiling, fuel and all bolt ons) with a lightly ported head and turbo to match (yet to make a decision possibly gtx3582r or similar from Hypergear) I've seen the Tomei kits with just the buckets getting around, Supertech sells most things - Supertech High Performance Cam Followers | Trusted Racing Cam Followers Questions -  Has anyone found the Hydraulic lifters to limit them at this power level? Is it usually found that you can just clean the stock lifters and find they work fine?  Does going solid lifters save any headaches/issues with hydraulic lifters in the future? Any recommendations on other things that will need to be replaced, I know I'll need to get the solid profile cams but can you use the same type of valves and springs/retainers and is it recommended to change the guides and stem seals?    Summary -  Basically looking for pros/cons and wanna know if I'll actually need the extra RPMs from solid lifters or it'll just be bragging rights to say it ReVs OvEr 8000 Cheers
    • Ha ha ha, this stuff they had was installing Toshiba PLCs that were made some time in the 1990s, and they were replacing GEM80 PLCs. To let those two talk (staged upgrade along a ~1.2km long building that was split into 4 sections), was a bunch of WinXP machines running Java gateways... There was no way to put something like ProfiSafe in... Most of the HMI machines were WinXP, with Java program, with a custom button board emulating a keyboard... About the only buttons in the operator stations that went direct to the PLCs was the eStop. There was some interesting design stuff in that place...
    • Stock bypass valves are good for plenty of boost.
    • Check for fuel flow out of the outlet end of the rail. Check for spark. Try to start with aerostart (or pressure can brake cleaner or similar solvent in a car) prayed in through TB. If you have fuel and you have spark and it will fire on substitute fuel, then seriously suspect that E85 sitting for ages in your fuel system has destroyed something and put it in your injectors.
    • Nissan stock oil pressure is typically about 1 bar at 1000 rpm plus about 1 bar per thousand revs on top.
×
×
  • Create New...