Jump to content
SAU Community

R32gtr Parts - Trim, Coilovers, Steering Boss Kit, Braces


braydenthegolfer
 Share

Recommended Posts

R32 GTR Parts: - Coils, Braces, Boss Kit, Door Cards, Guage

-R32 GTR Steering Boss Kit came off Momo wheel - $50.00

-HKS Mechanical Boost Guage in bar - $110.00

-R32 GTR Door Cards in used condition fabric is fine but vinyl has lifted in corners a little. Have front and Rear Available -

-Front R32 GTR Door Cards - $100.00

-Rear R32 GTR Door Cards - $70

OR BUY BOTH $150.00

Also have Window Switched Left and Right $80.00

- HKS Adjustable Coilovers in Good Working Condition- $750.00

- Front Strut Brace - $100.00

- Rear Strut brace - $100.00

Also WTB: WANTED TO BUY:

- R32 Rear Window trim (C Pillar)

- R33 Nissan Centre Caps

Located North bris

Can Post or Meet up if required.

Brayden Zero405639821

post-78006-0-15870400-1422226003_thumb.jpg

post-78006-0-84107600-1422226079_thumb.jpg

post-78006-0-87133400-1422226131_thumb.jpg

post-78006-0-76781700-1422226309_thumb.jpg

Link to comment
Share on other sites

  • 2 weeks later...
  • 3 months later...
 Share



  • Similar Content

  • Latest Posts

    • Much less twat-tastic. CF wheels are too garish for civilised use.
    • From there, as the manual says....assembly is the reverse of disassembly, no tricks worth mentioning Much better (for me)
    • In my case, the standard wheel I had was in good condition but the buttons had more wear, so I swapped them across from the original wheel from the car. The plastic rear cover is held on by 4 tabs, and once the wiring is removed you can get access to 2 screws on each side the hold the buttons in From there I just swapped the wiring over. What was interesting is the standard style wheel is 2.0kg but the carbon fibre one is 50% heavier at 2.9kg. It even has a weight inside the wheel at the top to make up for some sort of imbalance in the design. weird
    • Once the airbag is off, to remove the steering wheel.... Undo the 2 plugs into the clock spring, and the horn connector from it's clip. Hit the 19mm nut with a rattle gun (preferably) or if you don't' have one, you probably want an assistant to hold the wheel in place while you use a breaker bar to undo the nut Then, screw the nut back on 3 turns, and pull the wheel sharply towards you. If that doesn't work hit it medium force with a rubber mallet on either side, or possible behind if you can get there. If that all fails (it shouldn't!) you might need a steering wheel puller
    • So, to next task....the carbon fibre steering wheel was either an expensive factory option or a chinesium special. Either way, I don't like either the flat bottom or thick ring style, so it had to go So...to remove the steering wheel.... First, disconnect battery negative and stomp on the brake pedal for a few seconds. Then, remove the small circular covers on each side of the wheel's rear surround to uncover the airbag clips. You need to push something like a flat bladed screw driver through, to push the steel clip inwards and pull the side of the airbag forward. Once you've done the easy side, same on the centre console side. You can see the tab you are shooting for circled in red Then, disconnect the horn spade connector and for the yellow airbag plug you need to get something small under the black locking tab to pop it out, then the connector releases......airbag is off  
×
×
  • Create New...