Jump to content
SAU Community

[vic]full Rb26 Build Part Out. Nitto, Tomei, -5 Turbos,

Dobo
 Share

Recommended Posts

Dobo Contributor

Dobo

Posted
Posted

Rb26 bit clear out:

BRAND NEW Nitto H beam rods, nitto/je pistons at 86.5mm and nitto oil pump - $2500

rb26 garret 2860-5s. Have hks actuators and stainless dumps with them. After $1500.

R33 GTR RB26 stock pistons and rods - $150

BRAND NEW Tomei type B poncams, tomei type A valvesprings and titanium retainers - $1400

I also have 1000cc injectors, a dissassembled block and head as well as a complete motor worth of bits ready to go but it needs machining and assembly. Inbox me if you are interested in the whole lot and we can work out a deal

10922564_10152517047521266_4403516158582

1466203_10152517047646266_439188958147251966751_10152517048641266_91626916377580

10690142_10152517048691266_3887677349311

10340016_10152517048746266_3882781160050

10947274_10152517048786266_6335336873990

10470832_10152517048911266_6351926358457

10952547_10152517048941266_3882027390548

1374930_10152517048966266_87303894435307

Located in bacchus marsh, vic

Contact Stuart zero four 31716080

Dobo Contributor

Dobo

Posted
  • Author
Posted

bit of a breakdown and no swaps

all of it is brand new unless stated otherwise. all prices are firm and if you want anything posted i will do it at your cost

ALL ITEMS LOCATED IN BACCHUS MARSH, VIC

OS Giken TS2CD clutch to suit RB25 gearbox. get yourself a decent twin plate clutch that is rated to 600hp. comes with flywheel and bearing carrier - $1500 firm (rrp on this clutch is $2200)

Nitto H beam RB26 rods - $600

Nitto 86.5mm pistons - $1000

nitto oil pump - $1100

or ill do the nitto stuff in a bundle for $2500.

tomei poncams - $700

tomei type A valve springs - $300

tomei titanium retainers - $450

or i will do the tomei stuff in a bundle for $1200

ATi damper and underdrive pulley for water pump - $600

ID1000 top feed injectors with collars and plugs - $700

ARP head stud and main studs - $450

ACL race series standard size rod and main bearings - $200

os giken in/ex camgears - $300

tomei sump baffles - $200

nitto rb26 engine gasket kit(pretty much everything exept for head gasket) - $200

RB25 cam cover baffles with E85 safe foam - $200

nismo RB thermostat - $80

spool head drain kit - $150

walbro GSS 341 in tank pump - $80

tomei 87mm x 1.2mm head gasket with oil restriction for the block - $350

gates timing belt - $80

cometic MLS exhaust gasket - $10

now onto the used RB26 engine bits

garret 2860 - 5 turbos, have no shaft play. they have HKS actuators on them as well as stainless dump pipes - $1200

R32 GTR Nistune ecu, afms and loom. currently tuned for dash 5 turbos and bigger injectors and stuff - $600

R33 RB26 head. has cams and cam caps still in it. also has the intake and stainless exhaust manifolds and stock R33 turbos. will have either painted cam covers or stock ones and will either have stock injectors or just a fuel rail..... after $1300 complete with the painted covers or $1000 with just the normal covers and no injectors

RB6 block, stock crank pistons and rods and whatever bolt ons i have for it - currently disassembled - $600 with the sump or $500 without

  • 2 weeks later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The spray cans were in the "Kiln" room whilst I was preping the parts,  so probably around 2 hours to get them warmed up, the kiln room has 3 small ovens running at 100°c, 3 medium sized ovens running 100°c, and the large one I used running at 80°c, the room itself was about 28°c, I also spent a bit of time taping up the parts in the room as well, and by the time I was done I would assume that the parts were around that 28°c As for power, I expect a couple of Killerwasps up high would be achievable with the current mods, I'm still running the MZR 2.0 intake and throttle body, and there is a slight mismatch with the 2.0 intake (smaller) and 2.5 intake ports (larger) on the head, this intake is matched and specifically designed to fix this issue with the ports mismatch, the throttle body is also a couple of mm larger, OEM is 65mm, the Bosch is 68mm In the end it will look "prettier" than the molded plastic thing that is the OEM MZR 2.0 intake As for the LSD, it's the OEM Torsen which works fine for what I use the car for, plus, basically no maintenance apart from the occasional oil change
    • Pac
      The New Official S A U - N S W Spotted Thread

      By Pac · Posted

      I was at Tunehouse in Marrickville (great team over there really know their VR's) , and I spotted this Very clean R35.  
    • Pac
      Who has a Infiniti Q60, Q50 (V37)?

      By Pac · Posted

      Mate , I have the same issue right now with the exhaust noise , if you can tell me what your local guy did , I'll talk to my guys and see if they can do the same. Power is good but it just too loud when put it down. 
    • Komdotkom
      NC MX5

      By Komdotkom · Posted

      The other trick I've found with wrinkle black is to put the can in hot water for a bit to warm the paint up, and to pre-heat whatever you're painting. It'll be interesting to see if you pick up any power with the intake, following with interest. Got a proper lsd for this?
    • Dose Pipe Sutututu
      Intercooler Choice

      By Dose Pipe Sutututu · Posted

      Plazmaman 76mm Pro Series, done. Data to back it up, I posted up somewhere here a few years back
×
×
  • Create New...