Jump to content
SAU Community

Recommended Posts

Hi all

I'm having an issue with my silver top RB20 intermittently not starting properly. If I turn the car on and it's dead cold it starts but if I turn it off straight away and try to start it again it sometimes wont start or even sound like it's close to starting. For it to start again it needs to left for several hours it seems.

The car has been sitting for the last 6 months however prior to that I've had no trouble with it starting in my 5 years of ownership.

At one point when it wasn't starting it ran out of fuel I think (dodgy fuel gauge) as the pump started making a loud noise. I've since filled it up so the fuel in it should all be fresh.

I also had an issue with the car running badly above 2000 rpm and swapped to a new AFM however this hasn't changed the starting issue at all.

If anyone has any suggestions that would be great as I'm at a real loss at what to do :(

Link to comment
https://www.sau.com.au/forums/topic/453454-rb20det-starting-issues/
Share on other sites

When this happens, try and unplug your water temp sensor on the coolant neck. It's the 2x wire one that goes to the ECU, see if that helps or unplug the AFM

It could be when your car is warm/warmer the cranking enrichment isn't enough to get the motor going.. it could be a mixture of things, dirty/faulty AFM, faulty FPR, dirty injectors, etc.

Changed the spark plugs today, while the car seems to run smoother now it didn't change the starting issue :(

I tired unplugging the wire on the coolant neck while it wasn't starting but that didn't make a difference.

I should mention that I've been turning the car on for max 30 seconds before turning it off and trying to start it so I don't think the problem is really heat related. That said if you leave it for a few hours and come back it will start first time.

How would a go about testing the fuel pump? And could that cause an issue with just start up?

Changed the spark plugs today, while the car seems to run smoother now it didn't change the starting issue :(

I tired unplugging the wire on the coolant neck while it wasn't starting but that didn't make a difference.

I should mention that I've been turning the car on for max 30 seconds before turning it off and trying to start it so I don't think the problem is really heat related. That said if you leave it for a few hours and come back it will start first time.

How would a go about testing the fuel pump? And could that cause an issue with just start up?

did you disconnect the coolant sensor for the ECU or the one for the dash? the ECU one has 2-wires not 1...

(not sure how related this is to you but here goes)

do you have access to a wideband o2?

back in the days when I knew nothing about cars (10+ yrs ago).. I had the same issue with my RB20DET, a mate that was doing engineering at uni suggested I hooked up his wideband. Ended up finding out the car was running lean in general when it was in vacuum, turned out my injectors were all clogged.

As soon as got all the injectors serviced, new o-rings put in the car started easily and idle was back to stoich.

Humour me a little and just try a mates battery

Don't use a jump pack or try jump it off another car

Connect direct to terminals

Ps. Every time you try to start it and it doesn't start your plugs get a bit dirtier and eventually fouled again.

Edited by Sinista32

Just tried a battery out of a car that gets driven every day, had slightly higher cca as well. Result was still the same though.

While it wasn't starting I also took the line off the fuel filter and primed the car and tons of fuel came out. I don't know know if that tells me if the pump is working fine though.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • FWIW the depth of the groove in the rubber pad is not super essential, the blocks are rubber and squish a bit. If you are worried an angle grinder will make a deeper groove quick smart
    • I mean, if you were to move the jacking points away from the original location, that is, away from the wheels and closer to the centreline of the car, then it will be more likely to overbalance and tip off the supports. Same as we talked about before. I was talking about moving for-aft. If the sill is bent outward or inward, then the car would obviously look unstraight from the outside. Hopefully that hasn't happened either. Again, you can do comparative measurements from the chassis rails to see if there is much deflection.
    • Can you elaborate what you mean with your first sentence? I meant move as in the bulge kinda seemed like it got pulled "outward" meaning it got pulled down and to the side with the jacking rail itself, so the load bearing bulge now sits lower than usual and is not level with the sill on the other side of the jack point. Either that or the jacking rail just got pushed in a good bit.
    • As well as being risky WRT tipping off anyway. Yeah, I wouldn't expect it to move. Just measure from the rear one to the front one on the good side, then measure that same length on the wrecked side. You will find the notches in the pinchweld, and the jacking pad. Just spray a spot of marker paint or something there.
    • but any other area than the bulge you are talking about will just cave in then? The front driver side is pretty bent so I don't know if that will work the way it is now. I can still kinda make out where that bulge is/was but it looks like the position of it also changed due to all the mistreatment? Hard to tell
×
×
  • Create New...