Jump to content
SAU Community

Recommended Posts

Hi all,

I'm currently in the market for a good R32 GTR. Most rebuilt vehicles having forged pistons, rods, racing bearings tend to go for around $20-22k, while cars with stock internals can go from $15-16k.

I'd be happy with around 300kw atw and the car will only be used as a weekender; never planning to track it. Is it worth forking out the extra $5-6 for something with forged internals in my case?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/453580-worth-buying-forged-gtr/
Share on other sites

It's quite easily worth forking out 5-6k for a well built all round car. A forged engine doesn't always align itself With a quality car.

Like stated above if 5-6k worries you then maybe it's not the right choice, the more you cheap out with these things the more it will

Cost you in the long run.

"The poor man pays twice"

  • Like 1

The answer is yes, but not because it has forged pistons. It is worth paying extra for a car that has been competently reconditioned reasonably recently and for which there is evidence in the form of receipts, dyno sheets, maybe a compression test, road test and examination by someone who knows what to look for. If you can get a well looked after car then its is likely that the clutch is good, brakes and suspension have been properly maintained etc. GTR owners will tell you that they are money pits and if you can avoid expensive repairs soon after purchase so much the better.

  • Like 1

Its a GTR, expect it to cost money!

I'd be more concerned about getting a car without rust than one with a built motor. Engines can be replaced but rust had a tendency get worse before you realise that its really bad.

Hi all,

I'm currently in the market for a good R32 GTR. Most rebuilt vehicles having forged pistons, rods, racing bearings tend to go for around $20-22k, while cars with stock internals can go from $15-16k.

I'd be happy with around 300kw atw and the car will only be used as a weekender; never planning to track it. Is it worth forking out the extra $5-6 for something with forged internals in my case?

Cheers

I think when you talk about forged internals you really just mean a rebuilt motor. Yeah sure most people use forged pistons as they are cheap these days but for 300kW there is nothing wrong with Nissans pistons. In fact their ring package has much to recommend itself.

Anyway old story: Buy a nice one. If it has a rebuilt motor, good. If it doesnt thats fine too. But buy the car, not the spec.

  • Like 2

looks nice enough...do a proper compression test as a minimum....get underneath it and check all suspension bushes and diff bushes etc....check structure for rust...also check chassis rails for damage (common for them to be jacked up off the chassis rail)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • BOVs do have a purpose, if you ever log pressure before and after the throttle body, you will see a spike pre throttle on lift off from a WOT condition. Enough to bend throttle blades / damage e-throttle motors or simple assist in blowing off cooler pipes. FWIW, the above on really applies to those running at least 2 bar of boost. OP shouldn't have an issue, on the other hand, here are some videos of my shit box over a decade ago with some succulent dose with the airbox on and off. That shit box is unrecognisable these days 🫠    
    • I've tried all different combinations of BOVs/ no BOV and stock bypass valves over the years, on gear changes the stock bypass valve seems to get the car back on boost quicker because in part the turbos wheel speed isn't being slowed down by reversion, although they have issues holding boost much over the stock setting. Most aftermarket BOVs you can adjust the spring, tighter will make it open later and close sooner, but in my experience it'll cause a bit of flutter at low load/rpm anyway. I've also got some input into this whole no bov causing turbo wear, never had an issue on any on my turbos HOWEVER, I got my R33 GTST with 200k kms on it, with from what I can see still has the original turbo, no lateral shaft play but has about 4-5mm of play in and out which to me seems like a worn thrust bearing from years (100-150k kms?) of turbo flutter running no bov, so maybe there is some truth to it in the long run. But that'll never stop me loving the Stutututu while I have the car.   OP just wants to know if he can run a atmo vented BOV with no major issues and the answer is YES, plenty of people do it, there's no harm in installing it and seeing how it runs before spending $$$ on an aftermarket ecu, last time I bought a Nistune it was $2400 for install and a tune , unsure of todays prices but you get me. Crazy money to spend just to fix the minor inconvenience of stalling that can be overcome by letting the revs come down to near idle before putting the clutch in or a little bit of throttle to avoid it. You're better off leaving the ecu and tune for after a bigger turbo/injectors have been installed to take full advantage of the tune and get your moneys worth.   Let OP have his Whoosh sound without trying to break his bank haha
    • I see you missed the rest of the conversation where they have benefits, but nothing to do with avoiding breaking turbos, which is what the aftermarket BOV made all the fan boys, tuners, and modders believe was the only purpose for them...
    • But they do so for the other reasons to have a compressor bypass. It's in the name.
×
×
  • Create New...