Jump to content
SAU Community

R32 GTR questions

Ethan_R32
 Share

Recommended Posts

Ethan_R32 Community Regular

Ethan_R32

Posted
Posted

Hi guys,

well pretty soon I am getting an R32 GTR. I just have a few questions Id like to ask.

1. Is it possible to run it just in rear wheel drive on the dyno just by pulling the 4WD fuse?

2. What sort of power can I expect from full exhaust, intake, intercooler, boost up and maybe power fc or similar management, with stock turbos.

3. And what kind of 1/4 mile can I expect from these kind of mods.

4. What would a low 12 sec 1/4 be in an 1/8th mile drag? Because the only strip around Sunraysia is an 1/8th mile.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/4541-r32-gtr-questions/
Share on other sites
Fitzpatrick Speed Works Mentor

Fitzpatrick Speed Works

Posted
Posted

flat 8sec 1/8 mile is around 12-12.3 however dont be discouraged if it runs slower as you are only just starting on third gear over the 1/8 in a gtr, which hinders you as the skyline has alot more top end then people realise!! the fastest gears in a skyline releative to the gearing ect.. ect.. are 3rd and 4th. i would not be suprised to see a gtr run a 8.5 1/8 mile then do a low 12 high 11 1/4.

Link to comment
https://www.sau.com.au/forums/topic/4541-r32-gtr-questions/#findComment-71327
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      That's a given!  Bit hard to powdercoat it properly without removing them! 😁
    • Dose Pipe Sutututu
      NC MX5

      By Dose Pipe Sutututu · Posted

      No detail on compressor or turbine sizes, which doesn't help with housing size selection with that kit. However, from SR20DET mucking about and money torching perspective, a GTX2860R Gen 2 w/ 0.64 (46mm inducer) will do ~260kW on E85 about 1.5bar of boost. All in before 3000pm, which cause a gearbox to shatter. Now imagine the same turbo, on a modern motor with an extra 0.5L of displacement, and heaps of cam timing adjustability (not an on/off affair like the Nissan shit boxes). If this was my car (which I would never own or consider buying, ever!), I would go for a nice twin scroll setup, and a G30-660. Gates plumbed back, no silly shit. Lean on the cam timing, big displacement to create a flat-ish torque curve.  
    • The Bogan
      NC MX5

      By The Bogan · Posted

      98 mate
    • r32-25t
      NC MX5

      By r32-25t · Posted

      Do you plan on using 98 or e85?
    • GTSBoy
      NC MX5

      By GTSBoy · Posted

      This should be pretty easy. 200rwkW is just about the max power out of an RB25 stock turbo. So, 12ish psi on a 2.5L. That boost limited mainly by the prospect of seeing the turbine in the cat after the smoke show. A steel wheeled equivalent would likely happily do ~220rwkW at something like 17 psi, where it would probably be bumping into the usual limits of such a sized turbo. These things have like a .48 rear. You will not need the 0.86 rear. The 0.64 will be fine. In fact, if you were looking at various mid-200rwkW options for RBs, most of them would be in a 0.64 rear. So, I think you will definitely want to be no bigger than that for a same sized but probably even more efficient (at making power) modern engine.
×
×
  • Create New...