Jump to content
SAU Community

Lazy Oil Pump

DoseVader

By DoseVader,
in General Maintenance

 Share

Recommended Posts

DoseVader Enthusiast

DoseVader

Posted
Posted

Hi Everyone,

I was told on my last tune that my oil pump was starting to get a bit lazy at idle, its fine when it's got some revs behind it. What are my options here, I was told to try run a thicker oil or is it worth investing in a genuine/aftermarket oil pump? What are some good oil pumps to suit an RB25DET NEO?

Current car stats: 1998 R34 GTT 300hp on 13psi

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/
Share on other sites
jjman Mentor

jjman

Posted
Posted

Thicker oil.

What gauge were they using? I hope not the stock one.

Also it tends to be the engine worn out dripping pressure rather than the pump went out.

this and this.

but also, have you had the motor compression/leakdown tested? If the motor is too tired putting a highflow on it and upping the power a lot when the motor is potentially really tired will just result in a dead motor eventually (and poor results from the modifications).

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/#findComment-7486654
Share on other sites
DoseVader Enthusiast

DoseVader

Posted
  • Author
Posted

wouldn't hurt to do a leakdown test in the future but right now for the mods the car has its making the right amount of power so I am not to concerened about the engine being really tied. My guess is I need to run a thicker oil as I gets thiner as it heats up.

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/#findComment-7486694
Share on other sites
MrStabby Grand Master

MrStabby

Posted
Posted

Thicker oil.

What gauge were they using? I hope not the stock one.

Its not particularly easy to replace the pump, so I would be trying thicker oil first.

100% right.

DoseV, since you dont know what oil is in there now, contact the shop that did the service to find out what they use. If that doesn't work just get an average price dino first while you're trialling viscosities to see what works. Maybe assume they used a ?w-40 and try a ?w-50 first.

Once you've settled on a viscosity that works, step up to a good full synth and go the full 5000kms change interval.

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/#findComment-7487701
Share on other sites
GTRPSI Mentor

GTRPSI

Posted
Posted

So what oil pressure readings are you getting to call low?

10PSI for every 1000 RPM is all you ever need......

If your seeing 60 PSI or over at 6000, your good for 6000RPM, over 30 PSI at 3000, and so on.

Dont trust the factory oil pressure senders, make sure its aftermarket and post your results at each 1000 RPM.

Usually its worn bearings rather than worn oil pump giving the low readings unless your pumps bypass valve is stuck open or the pumps seriously worn and damaged.

A thicker oil will mask the issue.

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/#findComment-7487843
Share on other sites
jjman Mentor

jjman

Posted
Posted

100% right.

DoseV, since you dont know what oil is in there now, contact the shop that did the service to find out what they use. If that doesn't work just get an average price dino first while you're trialling viscosities to see what works. Maybe assume they used a ?w-40 and try a ?w-50 first.

Once you've settled on a viscosity that works, step up to a good full synth and go the full 5000kms change interval.

id assume any shop would do the easiest thing and just read the manual and put in the factory rec of 30w.

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/#findComment-7487975
Share on other sites
DoseVader Enthusiast

DoseVader

Posted
  • Author
Posted

I'm struggling to believe a tuner bothered hooking up an accurate gauge onto your engine.

Can you confirm with them how they can to the conclusion of lowish pressure?

I doubt they did as well my guess is the oil in it now is way to thin thus making the engine a bit noisy once the oil is warm at idle. But any way the car is going for a retune and full inspection in 2 weeks.

Link to comment
https://www.sau.com.au/forums/topic/454165-lazy-oil-pump/#findComment-7490769
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • kevboost7
      Magnetic Drain Plug Snapped in Half

      By kevboost7 · Posted

      Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs.  The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out.  It was a victory for me last night.         
    • MBS206
      New fix for low tyre pressure from bmw

      By MBS206 · Posted

      Yep, pretty much what you said is a good summary. The aftermarket thing just attached to the rim, then has two lines out to valve stems, one to inner wheel, one to outer wheel. Some of the systems even start to air up as you head towards highway speed. IE, you're in the logging tracks, then as speeds increase it knows you're on tarmac and airs up so the driver doesn't even have to remember. I bet the ones that need driver intervention to air up end up seeing a lot more tyre wear from "forest pressures" in use on the highway!
    • sunsetR33
      Anyone know this frontpipe?

      By sunsetR33 · Posted

      Yes, but you need to do these type certifications for tuning parts. That is the absurd part here. Meaning tuning parts are very costly (generally speaking) as well as the technical test documentation for say a turbo swap with more power. It just makes modifying everything crazy expensive and complicated. That bracket has been lost in translation many years ago I assume, it was not there.
    • dbm7
      New fix for low tyre pressure from bmw

      By dbm7 · Posted

      Hahaha, yeah.... not what you'd call a tamper-proof design.... but yes, with the truck setup, the lines are always connected, but typically they sit just inside the plane of the rear metal mudguards, so if you clear the guards you clear the lines as well. Not rogue 4WD tracks with tree branches and bushes everywhere, ready to hook-up an air hose. You can do it externally like a mod, but dedicated setups air-pressurize the undriven hubs, and on driven axles you can do the same thing, or pressurize the axles (lots of designs out there for this idea)... https://www.trtaustralia.com.au/traction-air-cti-system/  for example.... ..the trouble I've got here... wrt the bimmer ad... is the last bit...they don't want to show it spinning, do they.... give all the illusion that things are moving...but no...and what the hell tyre profile is that?...25??? ...far kernel, rims would be dead inside 10klms on most roads around here.... 😃
    • joshuaho96
      Anyone know this frontpipe?

      By joshuaho96 · Posted

      You're just describing how type certification works. Personally I would be shocked to discover that catalytic converter is not in the stock mounting position. Is there a bracket on the transfer case holding the catalytic converter and front pipe together? If so, it should be in stock position. 
×
×
  • Create New...