Jump to content
SAU Community

Recommended Posts

  • 1 month later...

NSW, VIC & SA have a suprisingly large number of stag fans and constantly are running stagea meets/events ect, wouldnt mind doing something like that in brissy but seems to be very few of us here.

I've seen alot of stagea's on the road in the bris/gold coast/tweed area but from what i gather, hardly any of them are on these forums. This makes it virtually impossible to try and co-ordinate any form of cruise/meet if we can't communicate with them.

I know Hugh and his son have stageas on the Tambo mountain (by the way Hugh, my parents are setting up a block of land up there now so i shall have to come and check out your Unicorns some time).

Maybe we need to liase with other clubs to try and find more stagea owners ?

which stagea page on FB - can only find WA & SA & Stagea enthusiasts pages..

ive been to quite a few meet in the last 12 months from downshift/layitlow/Otaku Garage and a few i cant remember and have one seen 2 x S1 C34 & 2 x S2 C34 & 1 x M35 stagea's in all of them and most ppl going to those (excluding Otaku Garage) dont know or care about the stags that do turn up as there more interested in skyline, supra, integera, wrx, holden, ford ect... Brisbane has a very.... average... car scene, most either wankers pulling skids and screwing for everyone else or only care about themselves... lots of up and coming photographers though...most under 20yrs...

  • Like 1

If anyone wants a premeet meet n greet pretty sure we could tee up something small easily enough - would just be aiming for something like Mt Cootha or somewhere with plenty of room with a view (for those that are good at taking photo's) but needs to be fairly central to everyone too

  • Like 1

Nah never been there before, been up Mt cootha, nebo, mee + climed a few at glasshouse but never been there. Might go for a trip on the weekend as its my last chance before the Stag goes in for repairs, insurance companies take so long to do anythign.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Exhaust end of this month, and then tune after that whenever there is availability. Still tossing up between a pure 98 tune or a flex 98/e85 combo.  The (lack of) milage in e85 isnt great. Start to get anxiety if i go for a long drive and there arent any united servo's nearby
    • I mean I can be OCD'y but this is really over the top. At that point why not just run a full wideband fuel controller? Especially if you run 3 widebands. The system works pretty well, which is trimming low load stuff to be within a few percent of the base map. Pre-engine _change_ the base map was only 1-2% off, depending on ambient temp, elevation, etc. Under load the LS is really very straightforward to tune, enough that a wideband closed loop would be overkill. If I really cared (and I hope I don't) I can always just go back to the MAF system the car actually came with. Which does all those nice calculations for me (temp, altitude, etc), now that you can buy 102mm MAF's that do not cause restrictions.
    • Good afternoon Team , just a quick update on performance mods  Current Mods list (Installed) HKS - Power Editor (Came with the car) looks to be some kind of boost controller RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Cat Back  RV37 Skyline 400R (SKYLINE) | FUJITSUBO  - Front Pipe AMS  - INFINITI Q50/Q60 RED ALPHA COLD AIR INTAKE KIT AMS  - Performance Heat Exchanger Intercooler Not Yet AMS Alpha Performance Full Race Down Pipes  - to be installed in May 
    • I'd be installing 2x widebands and using the NB simulation outputs to the ECU.
    • Nah, it's different across different engines and as the years went on. R32 era RB20, and hence also RB26, the TPS SWITCH is the idle command. The variable resistor is only for the TCU, as you say. On R33 era RB25 and onwards (but probably not RB26, as they still used the same basic ECU from the R32 era), the idle command is a voltage output of close to 0.45V from the variable resistor.
×
×
  • Create New...