Jump to content
SAU Community

R34 Gt Dying Need Help Asap

skiippy

By skiippy,
in Engines & Forced Induction

 Share

Recommended Posts

seejs Explorer

seejs

Posted
Posted

Don't rely on that remedy too much as eventually it will probably just die on you, best bet is to just but a new afm and be very careful when installing it, making sure you don't knock it or anything like that. For me the afm took a couple of weeks of running in for it to get rid of all the shakes. I'm just going off what happened to me when my afm shit itself and now my car runs fine. So I hope that helped mate and good luck :cheers:

Sinista32 Grand Master

Sinista32

Posted
Posted

Could have been just a loose plug by the sounds of your remedy. Wait to see if it happens again before spending cash on new.

No way will you get a new genuine AFM for $100 bucks. It's likely second hand for that price and could well be dodgey too.

New would be sub $300

ErOR Contributor

ErOR

Posted
Posted (edited)

If you still have the old AFM, take the cover off it on the side (the black square thing) and check the solder joints where the plug contacts meet the afm contacts. Mine has done this few months and and it's a 5min fix as the solder joints dried up.

If that's the case, take the plug out, clean everything and then re-solder the contacts, pop it back in and drive for a day or two to make it's all good. Than way you have a spare afm and have learned something in the process.

Edited by ErOR
XGTRX Veteran

XGTRX

Posted
Posted

If you still have the old AFM, take the cover off it on the side (the black square thing) and check the solder joints where the plug contacts meet the afm contacts. Mine has done this few months and and it's a 5min fix as the solder joints dried up.

If that's the case, take the plug out, clean everything and then re-solder the contacts, pop it back in and drive for a day or two to make it's all good. Than way you have a spare afm and have learned something in the process.

Don't worry about it, people don't listen, people would rather spend $380 than follow a diy that would take them 30 minutes and $30 on an iron and solder. It's such an easy fix for such a common problem. I just don't understand.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • soviet_merlin
      RH9 R32 GTR Build Thread

      By soviet_merlin · Posted

      Oof, I will forevermore have those shredded gears in mind whenever someone talks about showing mechanical sympathy towards their car. Thanks for the photos, fascinating stuff!
    • Dose Pipe Sutututu
      RH9 R32 GTR Build Thread

      By Dose Pipe Sutututu · Posted

      Curious to see how the SpeedTek stuff holds up
    • OST Micah
      RH9 R32 GTR Build Thread

      By OST Micah · Posted

      The holdups last year were drivetrain related. I had the car out right after getting the bearing issue resolved. Third launch and the car didn't move after releasing the clutch. It had sheared all the engagement teeth off the 1st gear.    Thankfully no other damage was done. I set an aftermarket gear beside an OEM gear and found that the engagement teeth on the OEM gear were much larger and better supported. Looking through my bin of spare transmission gears I found that there are two types of tooth on the OEM first gears - the larger tooth and the smaller tooth. It looks like most aftermarket gearset manufacturers base their design on the smaller tooth. OEM large tooth left - Speedtek, OS Giken, etc or OEM small tooth right Decided to give that larger engagement tooth a try. Pressed the ring off an OEM gear and sent it to a transmission manufacturer here in the States. They did their "faceplating" operation with my synchro ring on the Speedtek gear.   I reassembled it, took it back to the track and promptly destroyed the gear itself.  I'll rebuild this and use it as a spare - thankfully just first gear and the countershaft are damaged beyond repair. Definitely disheartening but my welded on engagement tooth ring held up!  Moved to Speedtek's dog engagement design as the gears appear to be much stronger. So far they have taken much more abuse at the track. Also scored a Stillway lockout from the Netherands for super cheap. It's for some other RB transmission so it took a bit of fabrication to fit but honestly a very easy job. I also had to heavily modify the gates as they were very different.   Then for some reason at the last test and tune a silicon coupler below the throttle blew off and took out the radiator and fan. Thankfully it was in the burnout box and not down track. This car is really beating me up - I still haven't made a pass in it. Ran it through the gears many times on the street but it keeps biting me at the track.  Currently in the process of replacing the radiator and remaking the throttle pipe to remove the coupler and use a cast 90 and a vband. I WILL get this thing down the track...
    • Ozdavroz
      Dumb rich kid tries modding for the first time

      By Ozdavroz · Posted

      Covers most of the above points really. There's a few exceptions but most just see driving as an irritating but necessary task they must complete if they want to get anywhere on time. Also see it as a good time to show their awesome multi-tasking abilities on their mobile and/or doing their makeup.  
    • OST Micah
      RH9 R32 GTR Build Thread

      By OST Micah · Posted

      I don't believe I posted pictures of the second oil pump pickup I added so here they are. Data shows it gets oil pressure up to the relief pressure much earlier in the RPM. Is that important? Not likely... This was just another attempt to fix the bearing issues.   I also heavily opened up the inlet to the pump since it now had to flow oil from two pickups. I believe the diameter increased about 1/8".
×
×
  • Create New...