Jump to content
SAU Community

Recommended Posts

Hey SAU,
I have a r33 gtst manual which I've owned for about a year now. The car has had a weird hunting/idle issue since I've had it. I've plugged my ecutalk in to have a look and from what I can see the timing jumps up and down. I tried blipping the throttle a few times lightly and sometimes It would sit at 15 degrees at idle when it came back down from the revs with no dipping and hunting noise. When its fluctuating it can fluctuate from what I could see around 5 degrees to about 13. It does this a lot, no matter what the temperature is like or how long I've been driving for. It can sit normally at idle and be fine and then a few seconds later it will fluctuate and you can definitely hear it without needing to plug in any consult software.
I've always felt like the car just doesn't perform like it should. Feels weaker than most rb25s I've driven. Not sure what other info to post up but the only other reading from ecutalk that was being erratic was my O2 sensor voltage. Which at idle (Can be at 15 degrees or when its being erratic) will go up close to 1 voltage and then drop back down and then up again etc etc. This may be normal but I'm not to sure?
People have said to get another CAS and to get the timing reset. I was just wondering what the forum thought and what other things I could check out or any other info I can try post up from ECUtalk etc.

Timing fluctuations at idle are normal as the ecu uses timing along with the IAC valve to control the rpm.

Check for vacuum leaks and set the idle screw in the aac or IAC or whatever its called on a 33.

That broken cas mount is nuts!

I remember getting a smoke test done on the car to find a leak a while ago, and any leak that was found was fixed. The problem is still there since then.

The car seems to idle around 650-700ish when warm so I think the idle is correct.

If you have access to a timing light and can borrow a known good CAS you can quickly eliminate that as a problem (or not).

Or there is a tutorial on here on how to clean your IAC valve.

I broke 2 cas's by somehow not aligning them properly, don't ask how, but both times they idled weirdly and one time it went jerky and stalled and later found the shaft had broke off,

so be careful, I actually bit scared to put that cover on anymore incase the shaft doesn't align straight :wacko: , cant remember but theres some spacers or something involved...

Thanks for the replies so far everyone. I will have another look for any leaks and get around to cleaning the IAC this week then. I guess after that I will move onto finding someone to check the timing and maybe getting my hands on another cas for cheap to test.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Meh, At 60 years old, I have been doing dumb stuff for much longer than you mate, I am the true King And unfortunately I cannot be a maroon, as I am not brownish red As for not getting ITB's, the plenum intake will apparently show typical gains across the board and increase induction noise a bit, but, have all over less dort than ITB's Cost difference for the extra ITB dorts was significant though, the total parts for the plenum set up is "around" $2kAUD plus shipping, the ITB's were $4kAUD plus shipping, I was contemplating really hard about paying the extra $2k for all of the dorts, but weirdly, some form of common sense, from listening to the platform experts prevailed  As for the NA mod hate by some, I've had a few boosted cars, with all their inherent issues, I'm now looking at simplicity and legalities for a street car, maybe I'm just getting old, and I'm quite happy to spend some of the kids inheritance, 5kw at a time 🤣 And think of all the money I'll be saving on consumables that something with boost needs, like engines, gearboxes, diffs, clutches,  tilt trays... etc. etc. etc. 🤪
    • Haha.  I wouldn't say I am either but I've definitely been around it plenty.  I'm guessing you know the dial in is basically to make a handicap to level the playing field between racers.  The car with the slower dial in goes first and in theory if they run their dial in time and the faster car also does then they cross the finish time if they also have exactly the same reaction time - if you go faster than the dial in them you lose, but if you are too slow there's a good chance the other person will get to the finish line first. I'm normally supporting other cars but they were all pretty dialled and were egging me on to race as well, here's one of the cars I tune (Starlet) which ran within like 1 hundredth of its dial in through the competition: https://www.youtube.com/watch?v=inEBu-d9Gn4&t=69s
    • Where ever the fuel reg gets it reference is what I use to T into for map reference been a very long time so where it goes to plenum/runners I have no idea but never had issues. 
    • What ecu? Same shop every time? Same ambient temperature? If timing is correct then pull plugs and see if lean or rich. Dyno can also read different if they have changed ramp rate or not set tacho/speed properly  
    • I've never done dial in's just straight up, whatever that's called. I'm far from a drag (racing ) expert.
×
×
  • Create New...