Jump to content
SAU Community

Recommended Posts

Well I just got my New Apex Power FC in the mail this morning and I went out pulled to stock ECU and pluged the PFC in. When I turned to key on nothing happend at all. No Check engine light illuminated and the comander isn't lighting up or showing anything at all. I checked the Model # to make sure it's the right one for my car. Crank the engine and it wouldn't start. :(

Is there somthing that needs to be done to the unit before it will work? I looked at the english manule from the Apexi webpage and didn't see any steps I missed.

Link to comment
https://www.sau.com.au/forums/topic/45468-brand-new-pfc-not-working/
Share on other sites

dont put it in yourself. It best that the computer is put in by a mechanic and tuned straight away. I know someone that put it in himself with a new set of forged pistons. He drove it for a while untuned and bye bye new forged pistons.

my 2 cents

The plug is going in all the way. I am a mechanic by the way.

It's happened to me before... Just unplug it, check all the pins are still straight, and try plugging it back in again.

If it still doesn't fire up after a few tries, check the power wires going TO and FROM the PowerFC (yes the PowerFC has OUTBOUND power wires)...

Other than that, it could very well be buggered? It's just a straight plug-in, and it should turn on and let you switch off the boost control option (if you're not using the boost controller, you have to turn the option off in the menus, otherwise it won't start properly/idle)

dont put it in yourself. It best that the computer is put in by a mechanic and tuned straight away. I know someone that put it in himself with a new set of forged pistons. He drove it for a while untuned and bye bye new forged pistons.

my 2 cents

Err, why pay for a mechanic to do it? IMHO that's just a waste of money since a PFC is essentially a plug and play device.

Sorry, but your friend was just stupid. Driving around on a base map with a rebuilt engine is a silly idea.

LW.

Do you know someone with the same car?

Try it in their and see if it fires up.

When i put my pfc in the engine would turn over but not start and it kept loosing any setting we would change. The solution was to put a new earth into the loom and that solved the problem.

Before the ground was put in the loom did the ECU work? Mine doesn't do anything at all. I tried running a ground wire to the ECU case and it didn't make any difference. So how did you figure to run the wire. Did you have to add an extra wire in the ECU conector?

I installed my PFC - simply unplugged the stock ECU, inserted plug into PFC then screwed the bolt down to lock the loom in. I certainly didn't need to earth it.

As for it being a "Plug and Play" device... sure it'll fire up, and even run enough to allow one to drive around, but the mixtures won't be anything near what is required. I can't see how the fool destroyed his motor driving it like that - if he was driving the car hard then I can, but people who fork out lots of money to rebuild a motor and install an ECU usually know a lot about the product they're paying for.

I've noticed that some PowerFCs uses it's metal case to ground itself.

You can't just have it lying on the carpet, you need to screw it into the bracket in the kick panel which will ground the unit.

Others I have seen have worked fine lying on the carpet, so I dunno?

Dude - check that your AFM is wired properly and the right setting for AFM are there. And also check that your AFM is working OK (ie swap with another one)

I just had exactly the same problem - swapped my AFM out and all good. I just don't know if my AFM is stuffed or my wiring was wrong cause I had a Q45 (didn't work) and changed to a VG30DE AFM (worked)

Good luck :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I replaced the whole clutch line with the chase bays braided hose, I think it removes that loop, is it the short hose that comes immediately off the slave or is there a drawing in the manual to find what you’re referring to? It was just re-bled when I upgraded to the nismo slave, old slave worked fine but I thought that might help, didn’t change a thing. It’s like the first half of the pedal is pushing air and then when it finally actuates the master the friction zone is tiny. Makes it practically impossible to launch the car
    • Yep, that was one of the things we learned fast in the past with our MX5. When you drive with the top down, you are effectively standing out in the sun, 100% of the time, and not getting in any shade (because roads aren't shaded generally!). Just like standing out in the middle of a field on a sunny 27C day is a bit of a bad plan, so is sitting in a MX5 without sun protection.
    • I also just ordered some Frankenstein bolts and side mounts to fit a hard top Just in case I do find one, basically so it doesn't need to be fixed to the car with only the front latch.......and then gaffa tape to keep it in place for the RTN journey from wherever I get it
    • If your temps are fine now, you probably won't have any issues with where your vents are as they don't look right up at the windscreens high pressure area, so any differences when giving it the beans for extended happy laps would be minimal, but, they should vent heaps when stuck in traffic  Much like how that reverse cowl on my SS let "visible" heat out when stationary, but, because it was basically at the windscreen my coolant temps on the Hwy actually raised because air was being fed into it at speed (110kph), to only come back down to around 90° when I got off the Hwy And your 100% correct about the NC currently not needing vents, but, if I was to add a turbo, and a oil cooler and intercooler in front of the condenserand radiator, and then take it to the track???? It is apparently a recommend requirement if I don't want to worry about coolant or oil temp issues, but, any of the above are possible scenarios, over time As it sits now, with the triple pass radiator and stock air conditioning system, I have absolutely no issues with either temps or air conditioning efficiency, I've been basically daily driving thie car for the last month, both on the Hwy, and peak hour, bumper to bumper traffic, but, that's pretty much expected from basically a standard engine  Talking about no issues daily driving, it was 39° the other day and I was sitting in bumper to bumper traffic on the M5 and then M7, with the top down, and with the air conditioning blowing nice cold air on my feet, balls, and face, well, there was one issue, my head and arms got pretty sun burnt Note to self: leave a hat and sunscreen in the car for such days 🤣
    • I would agree, unless you need something specific to the HV motor/battery side repaired or investigated, any mechanic will be able to perform normal services, but if you prefer, maybe look for a mechanic who regularly services/repairs Nissans, the VQ engines are pretty common in the Nissan lineup.  Sorry, I can't make any suggestions, I don't live in Vic.
×
×
  • Create New...