Jump to content
SAU Community

Wiring Diagram for a Z32 AFM?

wannabe

By wannabe,
in Engines & Forced Induction

 Share

Recommended Posts

wannabe Proficient

wannabe

Posted
Posted

Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Link to comment
https://www.sau.com.au/forums/topic/45501-wiring-diagram-for-a-z32-afm/
Share on other sites
R31 POWER Mentor

R31 POWER

Posted
Posted

I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V

2 = AFM ground

3 = AFM signal

OMRAN Collaborator

OMRAN

Posted
Posted

hey mate ...

z32 MAF marked A to F but only four connections are used when fitting to the rb20det i think also rb25det (not sure )

A: Blank off

B: connect to Black wire

C: connect to black/silver

D: connect to white

E: connect to black with white trace

F: Blank off

you'll need the eprom remapped to suit

check out the pic

and good luck ... happy HP :D

  • 3 months later...
Trust33 Grand Master

Trust33

Posted
Posted
I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>  

1 2 3 4 5 6  

1 = no connect  

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect  

====ECR33 Flow===>  

1 2 3  

1 = 12V  

2 = AFM ground  

3 = AFM signal

Hi,Got to dig up an old thread

Does this mean that for the r33 all that is needed to do is to ground the z32 afm straight to the chassie.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal .... 3 on r33

3 = ground ..........straight to chassie

4 = AFM ground... 2 on r33

5 = 12V ...............1 on r33

6 = no connect

Targa Tom Proficient

Targa Tom

Posted
Posted
Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Gently remove lid, unsolder three pins, remove socket, do same to old AFM, fit socket, replace lid. Sika-Flex for seal.... Done.

TT

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Targa Tom Proficient

Targa Tom

Posted
Posted
And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>                      

1 2 3 4 5 6  

1 = no connect                                              

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect

====ECR33 Flow===>  

1 2 3  

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:D :wassup:

Make that unsolder "4"

:Oops:

Targa Tom Proficient

Targa Tom

Posted
Posted
weird why is that.And why would meggala say that it needs 4 wires to hook up.:D

I dunno, but I like to investigate alternatives, and for me it is easier to change the socket, and leave the loom in tact. Some prefer to solder wires and use heatshrink.

My method takes ten minutes from go to whoa... Each to their own.

Thats the beauty of having alternatives...

Anyone who is interested I have some pics zipped.

TT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      New fix for low tyre pressure from bmw

      By MBS206 · Posted

      I believe Unimog is the only vehicle that has it (from the manufacturer). I haven't seen aftermarket permanently connected kits, but I haven't looked either.
    • MBS206
      The Ls1 R33 Of Fury

      By MBS206 · Posted

      Ha ha ha, can't overthink when exhausted... Oh how I wish I had that power! I can be absolutely dead set shot, and my brain will still go "we need a good 3 or 4 hours to just think about everything and anything before you may sleep... My biggest thing is making sure I give myself enough sleep. I don't operate on even 7 hours of sleep! I attempt to give my body 9.5hours sleep a night to be able to function. I don't sleep the whole 9.5, but I need to make sure I offer a big window. I also take a single supplement, which is to help with long term health, and fighting inflammation, and I notice it helps massively. Especially me sleeping, and just less "achey" in the body. Have also kicked sugar, and gluten. A majority of people with ADHD don't go well with gluten. It causes a really interesting natural opioid overdose in the brain, which causes bodily issues and sensory issues.
    • Duncan
      New fix for low tyre pressure from bmw

      By Duncan · Posted

      Yeah that's what I meant, permanently connected not manual
    • MBS206
      New fix for low tyre pressure from bmw

      By MBS206 · Posted

      Yep. But typically that's just run a hose down to the tyre while stationary.   Oh and the Unimog will automatically air up and air down tyres from the onboard computer for you too.
    • Kinkstaah
      The Ls1 R33 Of Fury

      By Kinkstaah · Posted

      There was a good video somewhere, maybe Kurzgesagt that linked physical activity to ADHD/Anxiety/Insomnia etc. Basically the body WILL spend energy doing something if you don't spend it doing anything physical. It isn't fun, but I personally have noticed I've never been overthinky, or unable to sleep if I'm physically exhausted from doing a lot. The musings around it seem to indicate that this is one of the reasons/mechanism that physical activity improves mental health/wellbeing etc, by more or less not using that 'extra' energy to overthink, be anxious, inflammation, etc. There's also the fact that every obnoxious exerciser ever says it's great and helps which is extremely annoying. Like people who say the same thing about travel being the best thing ever. I mean, they clearly are, but blah. I started doing a LITTLE myself (think 3x15min per week) and honestly did notice the benefits, aiming at life quality when older. Which is sooner than you think. Getting something into your routine that you can actually make a routine has helped me at least. This post brought to you by procrastination between sets.
×
×
  • Create New...