Jump to content
SAU Community

Wiring Diagram for a Z32 AFM?

wannabe

By wannabe,
in Engines & Forced Induction

 Share

Recommended Posts

wannabe Proficient

wannabe

Posted
Posted

Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Link to comment
https://www.sau.com.au/forums/topic/45501-wiring-diagram-for-a-z32-afm/
Share on other sites
R31 POWER Mentor

R31 POWER

Posted
Posted

I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V

2 = AFM ground

3 = AFM signal

OMRAN Collaborator

OMRAN

Posted
Posted

hey mate ...

z32 MAF marked A to F but only four connections are used when fitting to the rb20det i think also rb25det (not sure )

A: Blank off

B: connect to Black wire

C: connect to black/silver

D: connect to white

E: connect to black with white trace

F: Blank off

you'll need the eprom remapped to suit

check out the pic

and good luck ... happy HP :D

  • 3 months later...
Trust33 Grand Master

Trust33

Posted
Posted
I hope this helps,I got this off this forum ages ago.

====Z32 AFM flow===>  

1 2 3 4 5 6  

1 = no connect  

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect  

====ECR33 Flow===>  

1 2 3  

1 = 12V  

2 = AFM ground  

3 = AFM signal

Hi,Got to dig up an old thread

Does this mean that for the r33 all that is needed to do is to ground the z32 afm straight to the chassie.

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal .... 3 on r33

3 = ground ..........straight to chassie

4 = AFM ground... 2 on r33

5 = 12V ...............1 on r33

6 = no connect

Targa Tom Proficient

Targa Tom

Posted
Posted
Hey All,

I was just wondering if I could get some information on how to wire a Z32 afm into my Series II R33 GTS-T (I have the appropriate plug.) A wiring diagram would be highly desirable but any info anyone could share with me on the topic would be most appreciated!

Just for the record I have done some searches but I have not had much luck. Sorry if I am rehashing old queries…

Cheers

Tim

Gently remove lid, unsolder three pins, remove socket, do same to old AFM, fit socket, replace lid. Sika-Flex for seal.... Done.

TT

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Trust33 Grand Master

Trust33

Posted
Posted

And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>

1 2 3 4 5 6

1 = no connect

2 = AFM signal

3 = ground

4 = AFM ground

5 = 12V

6 = no connect

====ECR33 Flow===>

1 2 3

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:) :wassup:

Targa Tom Proficient

Targa Tom

Posted
Posted
And thats how its done....Just curious but if you just dont connect the unessesary pins it wouldnt have an effect at all hence there would be no need to remove the cap and re-sikaflex it......And why would there be a need to do the same to the old afm? just unplug it replace it with the z32 wouldnt you?Picking at you a bit cause i have never got a straight answer.

Oh,i see what you are getting at.Gently remove lid, unsolder three pins, remove socket. Sika-Flex for seal.... Done.But what about the fourth pin for the ground,the r33 only has three pins and the z32 has a fourth does it get grounded to the chassie?

====Z32 AFM flow===>                      

1 2 3 4 5 6  

1 = no connect                                              

2 = AFM signal  

3 = ground  

4 = AFM ground

5 = 12V  

6 = no connect

====ECR33 Flow===>  

1 2 3  

1 = 12V to z32 12v

2 = AFM ground to z32 afm ground

3 = AFM signal to z32 afm signal

4..And finally the z32 ground straight to the chassie which is what i was geting at in my previous post..

:D :wassup:

Make that unsolder "4"

:Oops:

Targa Tom Proficient

Targa Tom

Posted
Posted
weird why is that.And why would meggala say that it needs 4 wires to hook up.:D

I dunno, but I like to investigate alternatives, and for me it is easier to change the socket, and leave the loom in tact. Some prefer to solder wires and use heatshrink.

My method takes ten minutes from go to whoa... Each to their own.

Thats the beauty of having alternatives...

Anyone who is interested I have some pics zipped.

TT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Using Trickle Chargers

      By MBS206 · Posted

      I have two German Shepherds that like to bite things that are in places they shouldn't be. Plus the cars/batteries on chargers are inside a locked garage, inside that fully fenced and locked yard. If you can get the car out, you can have it, as I'll be having one hell of a laugh at your expense.
    • soviet_merlin
      Using Trickle Chargers

      By soviet_merlin · Posted

      Looks like they changed the wording in the manual for the new model. I have a different model. Mine is CC1206. Not CC1206-XLI. Mine doesn't support lithium at all. I can't find the manual for my model online and they don't list the model on the Century website anymore either. In my manual it says what I quoted and that they recommend to not leave it on 🤷‍♂️ Sounds like you'd be fine with this one now.
    • soviet_merlin
      Coc or nox of nissan skyline

      By soviet_merlin · Posted

      Thanks for actually answering every single point! I noticed the date only after posting. And yes, looks like things have changed a little bit since then. FWIW, looks like Government Gazette No 253 has the current emissions test procedure. Sounds pretty reasonable altogether. One thing I learned from this is that it's possible to check whether a catalyst does any work by measuring the temperature. Catalyst outlet temp is at least 40°C higher than inlet temps if there is a reaction happening. I'd be curious to check this on mine but don't have a thermometer. Because purely going by smell it can't be doing much. Personally I'd be okay to pay for the test as long as it's within reason. My main concern would be to lose my rego because it definitely wouldn't pass the test in its current state. I'll see if I can do a bit more digging and see what's involved in doing this nowadays.   To be fair I don't think it's stopping many people from doing the modifications anyway. It just puts a barrier up to doing things right  
    • tomaytown
      Skyline R34 Non- Turbo

      By tomaytown · Posted

      Uhhh if anyone sees this - I bought a BRZ years ago, on my fulls soon so back on the market for the R34!
    • The Bogan
      newbie attempts the GTR life.

      By The Bogan · Posted

      Research research research, and tackle the important things first, like the rust, because as a wise old hippie and some crazy horses once said "rust never sleeps" Nothing good comes easy and fast, and nothing that comes easy and fast is typically good
×
×
  • Create New...