Jump to content
SAU Community

Recommended Posts

Hey Guys,

I have been playing around for a few weeks with my first water cooling setup. I had no clue what I was doing when I ordered all the parts but everything turned out pretty good! I like to do things a bit differently so I went with an aquarium chiller in place of a radiator. These are not for the faint hearted, there is a decent sized fan to keep the compressor and condenser coil cooled. The overall sound level is less than a single GPU's fans at full speed though. Its also bigger than my Bitfenix Prodigy case.. Just!

Ok so the basics of my setup are as follows;

EK Supremacy EVO Elite cooling an i7 4790K

EK FC780 cooling a single Gigabyte 780Ti Windforce OC

XSPC D5 Photon 270 reservoir/pump combo

TECO TK500 Aquarium chiller

You can use a much cheaper chiller than the one I opted for, but I figured a quality one will last longer and handle the "different" usage of trying to cool an overclocked gaming PC!

In terms of overclocks I'm pretty happy with the results. My CPU is a poor overclocker and I couldn't get a stable clock above 4400MHz using a Corsair H100i but I managed a stable 4800MHz clock using the aquarium chiller. This took 1.45V core voltage and temperatures were higher than I wanted, 70-80 degrees under sustained full load. But 1.45V with the H100i hit 100 degrees in literally 1 second and crashed the PC! I tried higher than 4800MHz clock but it crashed and I think it was because the maximum multiplier is 48. After that you have to adjust frequency? Not too sure. I have settled on a 4600MHz overclock at 1.35V to keep the temperature lower.

On to the GPU, Gigabyte factory overclocked the 780Ti to 1020MHz. I have pushed that to 1160MHz and I see a permanent boost clock of 1315MHz due to running so cool! That's almost 100MHz more than I saw on air while I was regularly reaching 80-85 degrees where the boost clock would drop.

I normally run the coolant temps at around 25-30 degrees but can go as low as 10-15 degrees while gaming but there is no benefit with my overclocks.

I will get some pictures up as soon as I can, they won't be pretty as it's still in test setup but should give you some idea of what's been done. I do plan on running SLI graphics and I think that will be the limit of my small chiller, I calculate its capacity at roughly 450-500W.

Throw some questions at me or call me stupid, whatever you desire. I had very little information on doing this so maybe someone on there could benefit if they ever wanted to try this out.

Power consumption is about 100W. The unit uses 220W but only runs for 25 minutes of the hour. More than a normal radiator and fan setup but not enough to be worried about.

cheers,

Shaun

Link to comment
https://www.sau.com.au/forums/topic/455095-water-cooled-chiller-setup/
Share on other sites

On a side note, my Corsair (h80i I think) leaked while the cheap Coolermaster 120V is still going strong.

So disappointed in Corsair.

I've got a H100 and it's powering along. Had it for probably 15 months or so.

I didn't bother measuring pre and post temps but gut feeling is it runs probably 10-15 lower than on air and a lot mroe stable, ie. no big spikes when pushing it really hard.

I found with CPU cooling that unless you de-cap it you will never get the low temps you can achieve at the GPU. I have not de-capped a CPU before and I don't think its really worth it as some CPU's just wont overclock well even if temps are good! Years ago I had a CPU at minus 30 degrees under idle and under full load was at 10 degrees. Luckily that CPU was a good overclocker (i7 920 stock 2.66GHz, 4.8GHz overclocked and stable) I then used a i7 930 which is 2.8GHz stock but couldn't get a stable overclock above 4.5GHz.

As for the H100i, I had no issues with it. I know they had an issue with them leaking when they were in sub zero temps in the airplanes that were delivering them.

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I would paint match the whole thing to avoid unwanted attention  I had a similar bonnet, paint matched, on my old R33 GTST, but mine was a fibreglass jobbie made by Blitz in QLD, they work extremely well for radiator efficiency and under bonnet temps
    • Does anyone run this kit with factory plenum? Does the adapter and bosch tb fit under factory strut brace? I wanted to get this setup before going forward facing manifold. Thanks
    • small update time, after always wanting a "cool" looking bonnet for my car and always struggling to find one for the series 2 that i liked and wasn't an insane amount of money. Saw one i liked on RHDjapan from D-speed in Japan the price was very good for a carbon bonnet so good infact i was a little unsure how much i trusted it, decided to bite the bullet and with the help of jesse streeter in not long at all it was at my door. Once it was delivered i ran in from work and quickly unboxed it and to my surprise the quality was actually pretty good i quickly removed the old bonnet and placed on the new one to test it out and even the fitment wasnt too bad at all. Then decided to paint the little grille in the bonnet black to stop it sticking out so much.   I decided to not mess around with the hood latch and just install some aero catch hood pins, having never installed them before did some YouTube university classes and i was good to go. fair to say it is not a fun job at all from making brackets so the pins sit nicely and actually cutting through the bonnet but also being very scared of cutting the holes too big it took wayyyy longer than i would like to admit but finally got it there. Then it was time for a quick test drive to ensure the latches actually worked and thankfully the bonnet looked very stable. I still think paint matching the bonnet and leaving just the part that sticks up as carbon would help make it all look alot neater as im not sure how i feel about all that carbon on a very fridge white car but will leave it as is and see how i feel with time.  
    • I think it's bound to happen, you finally get it all perfect, and bam, something will happen. I took a while to get a Commodore rear quarter repaired where a P Plater clipped it. Two days after getting it back, Sarah wiped it out on a concrete pillar in an underground car park... This is why I take forever to repair them, it stretches how long until it gets bent again... 😛
    • Nah, not really responsible for that little fiasco, but I'm still pissed at myself for writing off my 86, or when I reversed my VX into a pole just before selling it, but, meh, 5hit happens to stuff, all it takes is a slight distraction, and life is full of distractions, and "dooh" moments   
×
×
  • Create New...