Jump to content
SAU Community

Discussion About Gtst, Are They P Plate Legal.

White5tar
 Share

Recommended Posts

niZmO_Man Grand Master

niZmO_Man

Posted
Posted

Well of course checking the RMS website they're not legal but apparently there are people saying that the factory stock "aus spec"GTST are p plate legal. So my question is what do you think is it p plate legal or not?

When you get done for driving an illegal car, will these "people" help you? That's a better question you should be asking.
Trex Grand Master

Trex

Posted
Posted

Or do wut I'm doin. I'm usin the rb26 with rb20 rods pistons and frank. Ultimate sleeper! No cops gunna no. I'm also hownin and borin the inside and outside of the blok to up the compression to bring on boost easier because of the shitty 26 block.

Heaps of write ups how 2.

r32-25t Grand Master

r32-25t

Posted
Posted

The gtst that was brought in by nissan australia is legal for p platers but they are rare to find, so you need to make sure it has the silver compliance plate and not the green or purple one.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By GTSBoy · Posted

      It's (the TPS) buzzing? Or something else is buzzing in response? Remove the IACV from the plenum. Block the hole into the plenum with your hand. Get someone to start the car. Let some air is. Do the revs flare up? This is checking that the path into the plenum is clean. After that, is the air hose leading to the IACV fuly clear? After that, either you didn't clean it thoroughly enough to allow the valve to move, or it is broken.  
    • wizlb
      Finding E-30 & E-85 in Sydney

      By wizlb · Posted

      Thanks Duncan 
    • sunsetR33
      ugently need expert / experienced opinion

      By sunsetR33 · Posted

      Just a follow-up on this topic. From what I can tell so far the rusty residue on the engine block might be unrelated to a coolant leak or maybe just older than anticipated. After driving it from the winter garage to my friend's garage I could not see any new traces of coolant leaking there, but I will test this properly once I was able to fully warm up the car and drive it for a bit. I think I can agree that the whole porous engine block stuff is kind of nonsense, but there is just a silly amount of true, false and half-true information on anything Skyline-related on the internet.
    • Butters
      UniClutch

      By Butters · Posted

      hrmmm , not mine , easter plans to pull engine not happening     
    • DRoc81
      R33 GTS25 NA - Stalling when vehicle is at operating temp

      By DRoc81 · Posted

      I removed the IACV, cleaned it and reinstalled.  I found a video on youtube that helped with the whole process, the guy then said the idle needed to be set, so the process was to get the vehicle up to operating temperature, unplug the TPS, set the idle screw in the IACV so the RPMs were around 600, then plug the TPS back in.  After I reinstalled the IACV, the car started (because, it was a cold start), once it warmed up, the car died, I adjusted the idle screw to see if that helped anything, it did not, I had to wait about 3-5 minutes, then the car would start back up. Only to shortly cut out, and only crank.  I loosened the TPS to see if adjusting that would do anything, and when I would rotate the sensor clockwise, there was a humming noise, but it would go away when I got the sensor in the horizontal position.  It only made the hum noise with the key on.  What do you guys think? 20250414_172604.mp4
×
×
  • Create New...