Jump to content
SAU Community

Recommended Posts

hey SAU ! im a new member here so if this is in the wrong spot admins please move!

iv owned my 94 r33 gtst s1 for about 3 and a half years now and my good friend before me had it for 5. ever since he has owned the car the hicas light will stay on and the hicas will not work!. but every once so often (normally after a rain storm) the next morning when i start the car the hicas light will be off the steering is light and hicas is fully working. so go to the gas station shut it off restart it and bam hicas light heavy steering, the hicas is no longer active.

now i know alot of you will say just get a lock out bar. but id really like to find out this problem before resorting to a lock out bar ()not that im agianst it im just super interested in the hicas system its self) no one in my area (canada) knows anything about hicas systems. so i thought i could pick the brains of a few more experinced guys.

i have tryed getting it to go into diag. but its never worked for me even one day when the hicas was active i tryed it and nothing.. (either im doing it wrong. or its just not going into the diag.)

any help would be awesome. thanks SAU

Link to comment
https://www.sau.com.au/forums/topic/456510-hicas-problem-r33-s1-gtst/
Share on other sites

How are you trying to get it into the diagnostic mode?

The HICAS system and the low speed steering assistance are tied together as you've found out. There are speed sensors in front hubs and the steering angle sensor behind the steering wheel which are crucial. In the R33 the system is electronic so maybe there's a bad connection somewhere. Take out the HICAS ecu and pop it open to see that inside everything is ok, as sometimes a screw can get loose and it can create electrical shorts.

Hence why I asked about an aftermarket wheel - because if the boss for the wheel does not have the drive peg for the steering angle sensor you;

a) get a HICAS fault and light on,

b) can't get it into diagnostic mode because the bloody steering angle sensor is needed as part of the song and dance.

The best answer when trying to diagnose this shit is to take it to a workshop with a decent scan tool (a Nissan dealer at the worst, any good general mechanic otherwise) and plug it into the Consult port and interrogate the HICAS CU directly.

I would also check all the sensors front and rear just to make sure everything is connected properly. Would I be correct in assuming the front steering rack on a S1 has a sensor as the S2's do. You would be so pissed off if turned out to be just a crappy connection or a frayed wire because it does work sometimes.

Cheers

Neil.

hey guys sorry for the long reply. i belive the steering wheel was changed out to a stock r32 steering wheel. ill go over the sensors once i can get it into my buds shop. im thinking its a stupid connection and that would be why on more humid/rainy days it works but on warm ones doesnt. thanks for all the fast replies ill go over most of this and let you guys know whats up.

Check steering wheel sensor as suggested

If you have heavy steering when driving slowly it may be the HICAS ECU itself. I had this problem (mind you i have a lock bar installed) and it was just an ECU fault. Sounds similar to yours. Usually the first time i drove it for the day it all worked then as soon as i parked up went and did something and came back, started the car - heavy steering

I bought another ECU for about $50 second hand (was actually a newer model HICAS ECU) and has been fine ever since

Ideally, if you know someone else with a 33, swap the HICAS ECU's and see if your car starts working perfectly and their car starts playing up. That way you can confirm or rule it out without spending anything

Edited by 89CAL

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I'm aware, but unless you're actually seeing the voltage the ECU is seeing and you're able to verify the sensors are actually working I find it hard to just trust STFT/LTFT. I will say, logging the ECU comes naturally to me because it's one of the lowest effort methods of diagnosis and I do similar things in my day job all the time. Staring at 20+ charts looking for something that isn't quite right isn't for everyone. NDS1 allows you to log almost everything so that's normally what I do and then sort out the data later. 
    • Silly question, as I bet you've checked already, but the motor turns over by hand yes? I suspect Neil has a spare starter, though if not, I believe I have a spare R33 (or two) starter.
    • Yeah just run one of those posts to the Link like GTSBoy said. From google it looks like a "mishimoto boost controller" is a manual boost controller. Since you already have the link just buy any MAC valve and plumb it in where the mishimoto is now. Wires to the solenoid should come from the Link's / standard loom boost control wiring (I guess you have an r32, not sure if it is gtst or gtr, if it is GTR where is a 2 pin connector near the engine bay fuse box/injector resistor for that purpose, assuming the standard boost controller is gone)  
    • No. The ECU's hose is for a connetcion between the plenum (assuming single throttle body, not ITBs) and the ECU's internal MAP sensor. This is the primary load measurement of the ECU - so you need to get this one right. This has NOTHING to do with the boost contol. The wastegate also needs to see a boost signal - but it is actually far better for it NOT TO COME FROM THE PLENUM (again, assuming single TB, and not ITBs). This should come from the turbo's compressor housing (assuming there is a nipple on there, which there might well not be), or on the boost pipe somewhere between the turbo and the TB. On the pipe from the turbo to the intercooler is usually most convenient. The boost controller is then located between that boost source and the wastegate, ACCORDING TO THE CORRECT PLUMBING DRAWING FOR THAT BOOST CONTROLLER. There is no general diagram or instruction that will be correct for every case. Then the other ports on the plenum are for purposes such as Duncan described. If the boost controller has an internal MAP sensor, for a boost display, etc, then it will want to be hooked up there, alongside the ECU and the FPR.
    • Ok gotcha, so one post to fpr  another to bov  and I have the mishimoto boost controller and a link g4+ so I’d just have the tuner set it up properly. For the last two from plenum post throttle to  ecu/ boost controller, I know that I have a hose coming from the ecu that I was confused about so I assume that’s what connect to the boost controller from the ecu? And then the last is just from plenum to boost controller then to wastegate?
×
×
  • Create New...