Jump to content
SAU Community

Recommended Posts

Corey, what about jeeps? Few Cherokees around? Also looking at pajero's prado's pathfinders and maybe x5's

Stay away from jeeps unless you like catching on fire

Yes to prados, and x5's seem nice

Pathfinders are a pain to repair, especially the transfer cases and the electrics. Early Pajeros are good, the new ones had a recall from memory for overheating problems but they are weeding them out, gearboxes in them are strong but if you are going to tow campers/boats/caravans/race cars you may need to invest in airbags as they sag in the ass real bad

Leaning towards pajero's now. Only looking at putting 150ish on the ball. That only drops the rear of the zook 25mm so doubt the paj will sag any further. Unfortunately recently found out our car is good for 85kg only. Spewin cos it tows it well

Something like this Trev? Pajero's depreciate far worse than Prados so you can pick up a relatively late model one in good condition for considerably less $$

http://www.carsales.com.au/dealer/details/Mitsubishi-Pajero-2006/OAG-AD-7904802/?Cr=6

One of our mechanics had one, did 400,000 kms without too many dramas.

  • Like 1

120 Series Prado would be a good tow vehicle as well if you can find one at a comparable price to a Pajero.

http://www.carsales.com.au/dealer/details/Toyota-Landcruiser-Prado-2005/AGC-AD-18325346/?Cr=5

Petrol of course ;)

  • 3 weeks later...



  • Similar Content

  • Latest Posts

    • It was roughly 3.5 hours.    car went in around 11:00 and I was done around 2:30 He did the initial runs, install the BC and then Nistune install and tune.  The best part was sitting in the lobby and hearing the skyline on full throttle at the dyno 😂😂
    • Glad it all went smooth. How long did the tuning process take?
    • Yeah that was kind of the same feedback my tuner gave me.  the boost tee is until I can sort out my plan for the electronic boost controller and what I’d get, where I’d mount the dash etc.  I’m happy with this until I can figure it out. Not a big fan of the A-pillar gauges. I’d like to get a clean install of the boost gauge - something digital like GFB.  Something like that might fit neatly where the ashtray is and look clean. I feel like replacing the OEM triple gauge is a bit extreme for a weekender like my skyline. And it’s not making crazy power to need all the additional sensors/gauges. 
    • I'm about to swap my box to Tremec T56 Magnum F & initially thinking of re-using my DCS twin plate (can get it re centred for the bigger spline) but it's been called out the box will be noisy (rattle) as the clutch is unsprung.  So I'm doing as much research as possible. I'm not so worried about holding the power as I'll go the track version which on paper will hold the maybe 1000hp I make. It's the longevity I worry about. DCS told me they don't use a sprung centre as it's just something that can break. The uni clutch has a very complicated sprung centre. Any one had or heard about any issues with it failing? Thanks in advance.
    • Auto is at least 10% (from my real, actual experience with different torque converters and manual on the same setup) ~185rwkw at 11.6psi (peak!) is entirely what one would expect without a FMIC or anything else on the intake, it does bleed off towards the higher RPM so it's what, 9psi there? Note: There is nothing that can be done about this with a manual boost tee. If you want to hold it steady and gain more top end, well - You will need electronic boost control.....
×
×
  • Create New...