Jump to content
SAU Community

Rs Four Stagea With R32 Box To Rwd From Awd

Dan19

By Dan19,
in Four Door Family & Wagoneers

 Share

Recommended Posts

Dan19 Rookie

Dan19

Posted
Posted

hey guys i have a stagea rs four and i think it has a 32gtr box in it as it has a push type clutch same slave placing as a 20det box and i want to know as it has this box how do i put the damn thing into rwd mode without taking the shaft out..... please help also with my iacv is wound all the way out and im only getting 700rpms out of it and its pulsing idle does that mean its blocked up

Grimi Enthusiast

Grimi

Posted
Posted

if i remember correctly (there is a thread on this somewhere) you need to pull a fuse & the front drive shaft so you dont damage the box. I beleive the whole system runs rwd and only becomes awd when the rears start to spin.

One of the mor knowledgeable peeps on here should be able to say if im right or not. Also there is threads on this in here somewhere too.

KiwiRS4T Grand Master

KiwiRS4T

Posted
Posted

If it really is an R32GTR box c/w transfer case you should be able to just pull the 4wd fuses to get rwd. But if its an R33 box you will stuff the transfer case. There is a procedure for putting the R33 into RWD if you search. You'll also find a how to for cleaning the IACV valve.

But the safe way to go RWD is to pull the front driveshaft - its only 4 bolts.

GoldZilla Grand Master

GoldZilla

Posted
Posted

I have an R32 GT-R gearbox in mine and the tailshaft is ALWAYS removed whenever it needs to go on a RWD dyno or whatever. Better to be safe than sorry... Like Bob said, it's only 4 bolts.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shoota_77
      Shoota's R33 GT-R RB30/26

      By Shoota_77 · Posted

      They see me rollin' they hatin'....... Took me most of the day to make the necessary mods to the mounts to make them fit the car.  Fortunately I was able to just use the mounts that came with the rotisserie. The rear ones are really secure, the front I feel i might reinforce a bit more as it doesn't seem like enough attachment to the vehicle. I'm sure it's fine but better to be safe than (extremely...) sorry.  I drilled and tapped thread into additional M12 holes to each car mount where it attaches to the rotisserie as an extra fail-safe. Without them the side to side movement is just restricted by the allen head pinch bolts, nothing actually goes though the beam. Does now! I still need to adjust the rotisserie to get the car centred in terms of centre of gravity. If it's too high or too low relative to the rotational centre line of the car, it will be like a turtle and roll onto its back or as it currently sits, I dont think I'd be able to rotate it as it sits as it needs to lift the whole car up as it rotates. Ain't happening... I'm going to be nervous as hell the first time I go to spin it on its side...    
    • PLYNX
      BCNR33/ECR33 Door corner piece replacement

      By PLYNX · Posted

      Oh yes done this when the window started flopping around.  Turns out the guides that run along the rail chanel had crumbed way. Took off the door card and pulled out the window mech, then the window, which you have to pull out through the top. As said unbolt the guide rail and don't spend 30 minutes getting frustrated trying to find a way to slide it out upwards cause that don't frigging work. Drop it down and out through the door hole. All I did to repair it was slice some 10mm clear plastic tube, vertically, then screw it to the guide rail both sides. This tubing rolls inward on both sides and leaves a gap wide enough to hold the window. To finish all I did was lube the plastic tube with olive oil and Bob's your uncle . . . well if he has the operation he can be your Aunt ! !  10 bucks in plastic tube and another 5 minute job done again . . . . YEH BULLSH#T ! My love for Skylines knows no bounds !
    • BourneToLive
      R32 GTR Park lights issue

      By BourneToLive · Posted

      So was there a solution to this problem? I’m having this issue now. 
    • Duncan
      Beers and skylines Fatz style

      By Duncan · Posted

      not expensive, just irreplaceable if you don't go sub 60 at wakie in that thing people will start talking
    • Duncan
      BCNR33/ECR33 Door corner piece replacement

      By Duncan · Posted

      I haven't replaced that, but I have had the doors apart on the r32 a couple of times The door skin will be held on by a combination of clips and bolts, just take it slowly and make sure all the sneaky hidden bolts are out Once the skin is off you should be able to pop that piece off pretty easily, looks like there are only 2 bolts holding it on
×
×
  • Create New...